Configure Fax Passthrough A - Revision history

Allyntree: /* Applies to version(s): v2.6, v2.7. */

2013-07-22T15:09:18Z

Applies to version(s): v2.6, v2.7.

Allyntree: /* Applies to version(s): v2.6, v2.7. */

2013-07-22T15:08:50Z

Applies to version(s): v2.6, v2.7.

Cbilodeau: add v2.7

2013-07-17T15:54:24Z

add v2.7

Cbilodeau: fix content between v2.6 and v2.7

2013-02-26T20:49:59Z

fix content between v2.6 and v2.7

Clod Patry: adding header

2012-06-18T14:06:42Z

adding header

Clod Patry: Adding screen-shot for passthru using silenceSupp

2012-06-15T18:01:15Z

Adding screen-shot for passthru using silenceSupp

Clod Patry: created this page, print-screen will be added shortly.

2012-05-30T21:14:32Z

created this page, print-screen will be added shortly.

New page

To enable passthrough, follow these steps:
<pre>
1. Make sure "Enable Fax/Modem Relay" is enabled.
2. Make sure "Detection Mode" is Standard.
3. Make sure "Relay Mode" is Passthrough.
4. Make sure "Enable switching to FAX relay upon CNG tone" is checked.
5. Make sure "Detection type" is "Silence Suppression off"
6. Make sure the Codec is the same as the remote end.
</pre>

@@ Line 10: / Line 10: @@
 . Set '''Detection Mode''' to Standard.
 . Set '''Relay Mode''' to Passthrough.
 . Check the '''Switch to FAX relay upon CNG tone''' option.
 . Set '''Detection type''' to "Silence Suppression off"
 . Verify the the Codec is the same as the remote end.
 [[Image:Profile_passthru_silence_v26.png]]

@@ Line 2: / Line 2: @@
 {{DISPLAYTITLE:Configure Fax Passthrough}}
-To enable passthrough, follow these steps:
+'''To enable passthrough:'''
-<pre>
-. Make sure "Enable Fax/Modem Relay" is enabled.
+. Select '''Profiles''' from the navigation menu.
-. Make sure "Detection Mode" is Standard.
-. Make sure "Relay Mode" is Passthrough.
+[[Image:Profiles_0.png]]
-. Make sure "Enable switching to FAX relay upon CNG tone" is checked.
-. Make sure "Detection type" is "Silence Suppression off"
-. Make sure the Codec is the same as the remote end.
+. Set '''Detection Mode''' to Standard.
-</pre>
+. Set '''Relay Mode''' to Passthrough.
 [[Image:Profile_passthru_silence_v26.png]]

← Older revision		Revision as of 15:54, 17 July 2013
Line 1:		Line 1:
−	=== '''''Applies to version(s): v2.6.''''' ===	+	=== '''''Applies to version(s): v2.6, v2.7.''''' ===
	{{DISPLAYTITLE:Configure Fax Passthrough}}		{{DISPLAYTITLE:Configure Fax Passthrough}}

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.7.''''' ===
+=== '''''Applies to version(s): v2.6.''''' ===
 {{DISPLAYTITLE:Configure Fax Passthrough}}
@@ Line 13: / Line 13: @@
-[[Image:profile_passthru_silence_v27.png]]
+[[Image:Profile_passthru_silence_v26.png]]

← Older revision		Revision as of 14:06, 18 June 2012
Line 1:		Line 1:
		+	=== '''''Applies to version(s): v2.7.''''' ===
		+	{{DISPLAYTITLE:Configure Fax Passthrough}}
		+
	To enable passthrough, follow these steps:		To enable passthrough, follow these steps:
	<pre>		<pre>

← Older revision		Revision as of 18:01, 15 June 2012
Line 8:		Line 8:
	6. Make sure the Codec is the same as the remote end.		6. Make sure the Codec is the same as the remote end.
	</pre>		</pre>
		+
		+
		+	[[Image:profile_passthru_silence_v27.png]]