Configure Fax Relay C - Revision history

Allyntree: Needs revising edit

2018-03-08T18:40:20Z

Needs revising edit

2013-02-26T20:59:29Z

add needs revising category

2013-02-26T19:08:39Z

fix link

2012-07-13T12:44:04Z

Applies to version(s): v2.7.

2012-06-19T13:42:55Z

added note for upon CNG.

2012-06-19T00:40:36Z

Added "enable V.34 Fax"

2012-06-18T16:01:37Z

changing Detection type

2012-06-18T14:42:08Z

adding header

2012-06-18T14:41:14Z

Adding NSE to the table.

2012-06-18T14:34:47Z

Splitting the table in 3 parts

@@ Line 3: / Line 3: @@
 This is the list of fax Options.
-To see that list, you have to go in a Profile, then in section Fax/Modem Relay.
+To view the list of fax options, in the Web Portal, select Profile, in the navigation menu followed by Fax/Modem Relay.
 '''Fax Relay'''
@@ Line 108: / Line 108: @@
 [[Category:Glossary]]

@@ Line 103: / Line 103: @@
 *[http://en.wikipedia.org/wiki/Fax#Data_transmission_rate Wikipedia article]
-*[http://docs.telcobridges.com/tbwiki/NSE NSE]
+*[[NSE]]
 [[Category:Glossary]]

@@ Line 18: / Line 18: @@
 Standard: Fax tones and T.38 re-invites will trigger fax relay mode. Modem tones and passthrough re-invites will trigger passthrough mode, though fax detection will still continue.<br/>
 Use relay mode on any tone: Both fax and modem tones will immediately cause switch to the chosen relay mode (without going to passthrough first for modem tones).<br/>
-Always relay: Calls are directly invited using the specified relay mode, without waiting for any fax/modem tone. This improves performance when the calls are know to always be fax or modem (e.g. when connecting with a fax server).
+Always relay: Calls are directly invited using the specified relay mode, without waiting for any fax/modem tone. This improves performance when the calls are known to always be fax or modem (e.g. when connecting with a fax server).
 |-
 | Relay Mode

@@ Line 40: / Line 40: @@
 |-
 | Enable switching to fax relay upon CNG tone
-| This option indicates if the detection of a CNG tone will trigger a switch to fax relay mode. We recommend to leave this option enabled for faster switch to fax in most setup.
+| This option indicates if the detection of a CNG tone will trigger a switch to fax relay mode. We recommend to leave this option enabled for faster switch to fax in most setup.<br/>
 |}

@@ Line 51: / Line 51: @@
 | Use V.34
 | This option activates support for V.34 faxes. By using that option, faxes can be transferred at speed up to 33.6 Kbps.<br/>
-If disabled, only V.17 faxes will be supported (transfer speed up to 14.4 Kbps).
+If disabled, only V.17 faxes will be supported (transfer speed up to 14.4 Kbps). <br/>
 |-
 | Max bitrate

@@ Line 79: / Line 79: @@
 |-
 | Detection type
-| This option is used for different types of fax passthrough. Possible values are: None, Silence Suppression Off and G711 Only. None means no Passthrough will be triggered whatever the SPD is. "Silence Suppression Off" means when receiving an SIP invite, if the SDP contains the attribute "a=silenceSupp:off - - - -", it will be treated as a Passthrough call. When sending SIP invite as a passthrough call, the same attribute will be used. "G711 only" means if there's at least 1 G711 codec (ulaw or alaw), this call will be treated as a passthrough call. This is true when sending or receiving SDP.<br/>
+| This option is used to detect if a call will be in passthrough mode. Possible values are: None, Silence Suppression Off and G711 Only. <br/>
-This option works with the following option: Codec.
+*"None" means no Passthrough will be triggered whatever the SPD is. <br/>
 |-
 | Codec
 | This option specifies which codec will be used for fax passthrough. By nature, fax passthrough MUST be a non-compressed codec so you can choose between PCMU or PCMA. Note that when a switch to passthrough is initiated by the remote endpoint, our gateway will always use the same codec as the peer.<br/>
 |-
 | Jitter Buffer Depth

← Older revision		Revision as of 14:42, 18 June 2012
Line 1:		Line 1:
		+	=== '''''Applies to version(s): v2.7.''''' ===
		+	{{DISPLAYTITLE:Configure Fax Relay}}
		+
	This is the list of fax Options.		This is the list of fax Options.
	To see that list, you have to go in a Profile, then in section Fax/Modem Relay.		To see that list, you have to go in a Profile, then in section Fax/Modem Relay.

@@ Line 2: / Line 2: @@
 To see that list, you have to go in a Profile, then in section Fax/Modem Relay.
 {| cellpadding="5" border="1" class="wikitable"
 |-
@@ Line 37: / Line 38: @@
 | Enable switching to fax relay upon CNG tone
 | This option indicates if the detection of a CNG tone will trigger a switch to fax relay mode. We recommend to leave this option enabled for faster switch to fax in most setup.
 |-
 | Use V.34
@@ Line 59: / Line 67: @@
 | Transmission level (-1dBm unit)
 | This option is to adjust the transmission level to the TDM network. Valid values are between 0 and -15dBm, inclusive.
 |-
 | Detection type