Configure Fax Relay D - Revision history

Allyntree at 19:10, 9 December 2020

2020-12-09T19:10:52Z

Allyntree at 14:13, 1 May 2019

2019-05-01T14:13:57Z

Allyntree at 18:24, 7 December 2017

2017-12-07T18:24:52Z

Allyntree at 15:58, 10 November 2016

2016-11-10T15:58:43Z

Allyntree at 14:36, 8 December 2015

2015-12-08T14:36:52Z

Allyntree at 17:59, 9 March 2015

2015-03-09T17:59:00Z

Allyntree at 17:57, 9 March 2015

2015-03-09T17:57:23Z

Allyntree at 17:56, 9 March 2015

2015-03-09T17:56:20Z

Allyntree: /* Applies to version(s): v2.8 */

2015-03-09T17:54:28Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2015-03-09T17:50:34Z

Applies to version(s): v2.8

← Older revision		Revision as of 19:10, 9 December 2020
Line 1:		Line 1:
−	~~=== '''''Applies to version(s): v2.8, v2.9, v2.10, v3.0, v3.1''''' ===~~
	{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}		{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}
		+	{\| class="wikitable"
		+	\|-
		+	\|rowspan="3"\|This article applies to:
		+	\|'''Product'''
		+	\|'''Version'''
		+	\|-
		+	\|Tmedia
		+	\|2.8, 2.9, 2.10, 3.0, 3.2
		+	\|-
		+	\|SBC
		+	\|3.0, 3.1
		+	\|}

	This table presents a listing of fax Options.		This table presents a listing of fax Options.

← Older revision		Revision as of 14:13, 1 May 2019
Line 1:		Line 1:
−	=== '''''Applies to version(s): v2.8, v2.9, v2.10, v3.0''''' ===	+	=== '''''Applies to version(s): v2.8, v2.9, v2.10, v3.0, v3.1''''' ===
	{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}		{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}

← Older revision		Revision as of 18:24, 7 December 2017
Line 1:		Line 1:
−	=== '''''Applies to version(s): v2.8, v2.9, v2.10''''' ===	+	=== '''''Applies to version(s): v2.8, v2.9, v2.10, v3.0''''' ===
	{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}		{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}

← Older revision		Revision as of 15:58, 10 November 2016
Line 1:		Line 1:
−	=== '''''Applies to version(s): v2.8, v2.9''''' ===	+	=== '''''Applies to version(s): v2.8, v2.9, v2.10''''' ===
	{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}		{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}

← Older revision		Revision as of 14:36, 8 December 2015
Line 1:		Line 1:
−	=== '''''Applies to version(s): v2.8''''' ===	+	=== '''''Applies to version(s): v2.8, v2.9''''' ===
	{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}		{{DISPLAYTITLE:Toolpack: Configuring Fax Relay}}

@@ Line 4: / Line 4: @@
 This table presents a listing of fax Options.
 To view this list in the Web Portal, select '''Profiles''' in the navigation menu and edit the configuration to access '''Fax/Modem Relay''' options.
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 87: / Line 86: @@
 |Force V.152 VBD
 |Force V.152 auto-switch to Passthrough relay mode. This force the auto-switch without the SDP negociation.
-|-
+|}
-−

← Older revision		Revision as of 17:57, 9 March 2015
Line 89:		Line 89:
	\|-		\|-
	}		}
−
−	~~=== References ===~~
−
−	*[http://en.wikipedia.org/wiki/Fax#Data_transmission_rate Wikipedia article]
−
−	~~[[Category:Glossary]]~~

@@ Line 90: / Line 90: @@
+}
-== References  ==
+=== References  ===
 *[http://en.wikipedia.org/wiki/Fax#Data_transmission_rate Wikipedia article]
 [[Category:Glossary]]

@@ Line 43: / Line 43: @@
 |-
 |Switch to FAX relay upon CNG tone
+|Switch to FAX relay mode upon detection of CNG (FAX) tone. If disabled, switching to FAX relay mode will occur later, upon detection of v.21 flags, or re-invite from remote peer.
 |-
 |Switch to passthrough upon BELL ANS
+|Switch to modem relay mode (G711 passthrough) upon detection of Bell ANS tone (2225Hz answer tone).
 |-
 | Use V.34
-| This option is to support V.34 faxes. By using that option, faxes speed can transfer upto 33.6 Kbps.<br/>
+| This option supports V.34 faxes. By using this option, faxes can transfer data at speeds of up to 33.6 Kbps.<br/>
-If not checked, faxes will only supports V.17 faxes (transfer speed upto 14.4 Kbps).
+If not checked, faxes will only supports V.17 faxes (transfer speed up to 14.4 Kbps).
 |-
 | Max bitrate
-| This option is used to limit the maximum bitrate of faxes. By default, faxes will try to train at maximum bitrate. If a Failure to Train (FTT) happens, the bitrate will be reduced again and again. This option is used when you want to specify the maximum bitrate.
+| This option is used to limit the maximum bitrate of faxes. By default, faxes will try to train at a maximum bitrate. If a Failure to Train (FTT) happens, the bitrate will be reduced iteratively. This option is used when you want to specify the maximum bitrate.
-By using that option, faxes transmission will take less time, since no FFT will be negociated.
+By using that option, fax transmission will take less time, since no FFT will be negociated.
 |-
 | Fill bit removal
 | This option is used to remove inserted fill bits in Phase C for non-ECM data.<br/>
 We suggest to leave this option unchecked.
 |-
 | Redundancy Count
-| This option is to send multiple control frames, not FAX page data.
+| This option sends multiple control frames. Not FAX page data.
 |-
 | Transmission level (-1dBm unit)
-| This option is to adjust the transmission level to the TDM network. Valid options are between 0 and 15 inclusive.
+| This option adjusts the transmission level to the TDM network. Valid options are between 0 and 15 inclusive.
 |-
 | Detection type
-| This option is used for different types of fax passthrough. When receiving an SIP invite, Our
+| This option is used for different types of fax passthrough. When receiving an SIP invite.
 |-
 | Codec
-| This option specify which codec will be used for fax passthrough. By nature, fax passthrough MUST be a non-compressed codec. So you can choose PCMU or PCMA.
+| This option specifies which codec will be used for fax passthrough. Fax passthrough MUST be a non-compressed codec. You can choose PCMU or PCMA.
 |-
 | Jitter Buffer Depth
-| This option is to specify what will be the value of the fixed Jitter Buffer.
+| This option specifies the value of the fixed Jitter Buffer.
 |-
 |Packet Duration
+|Packet Duration for fax passthrough. Increments of 5ms from 5 to 60.
 |-
 |Use NSE
+|Enable using Named Signaling Event (NSE) when switching to Passthrough relay mode.
 |-
 |Support V.152 VBD
+|Support V.152 auto-switch to Passthrough relay mode. This forces the SDP attribute gpmd to be negociated.
 |-
 |Force V.152 VBD
+|Force V.152 auto-switch to Passthrough relay mode. This force the auto-switch without the SDP negociation.
 |-
+}