FreeSBC:SIP Trunking:Example A - Revision history

Serdar Civici at 12:25, 22 January 2021

2021-01-22T12:25:19Z

Luc Morissette at 13:38, 15 March 2019

2019-03-15T13:38:08Z

Serdar Civici at 09:08, 9 January 2019

2019-01-09T09:08:43Z

Serdar Civici at 09:35, 6 February 2018

2018-02-06T09:35:07Z

Serdar Civici: /* SBC Use Cases */

2018-02-01T06:27:35Z

SBC Use Cases

Serdar Civici: /* SBC Use Cases */

2018-02-01T06:26:07Z

SBC Use Cases

Serdar Civici at 06:25, 1 February 2018

2018-02-01T06:25:26Z

Serdar Civici at 05:57, 1 February 2018

2018-02-01T05:57:20Z

Cbilodeau: remove index (A) from display title to change page title

2018-01-31T18:08:31Z

remove index (A) from display title to change page title

Serdar Civici at 07:03, 31 January 2018

2018-01-31T07:03:00Z

@@ Line 1: / Line 1: @@
 === '''''Applies to version: v3.0''''' ===
-{{DISPLAYTITLE:FreeSBC:SIP Trunking:Example}}
+{{DISPLAYTITLE:ProSBC:SIP Trunking:Example}}
 =Introduction=
-The SIP Trunking Example Configuration  provides you with a step by step SIP trunking Configuration of [[FreeSBC|FreeSbc]] systems, using the Web Portal configuration tool. Complete general installation configuration steps, before you begin configuring your specific scenario.
+The SIP Trunking Example Configuration provides you with a step by step SIP trunking Configuration of [[ProSBC|ProSbc]] systems, using the Web Portal configuration tool. Complete general installation configuration steps, before you begin configuring your specific scenario.
 =SIP Trunking Example=
@@ Line 10: / Line 10: @@
 ==Prerequisites==
-[[FreeSBC|FreeSBC]] devices must be installed as described in their respective [[Product_Installation_SBC|installation guides]].
+[[ProSBC|ProSBC]] devices must be installed as described in their respective [[Product_Installation_SBC|installation guides]].
 =IP Network Configuration=
@@ Line 44: / Line 44: @@
 *Enter a name for the VLAN
 *If the port is to be used untagged, make sure '''Untagged''' is checked.
-*If the port is to be used with a 802.1Q tag, uncheck '''Untagged''' and enter a VLAN ID.
+*If the port is to be used with an 802.1Q tag, uncheck '''Untagged''' and enter a VLAN ID.
 *Click '''Create'''
@@ Line 83: / Line 83: @@
 *Enter a name for the VLAN
 *If the port is to be used untagged, make sure '''Untagged''' is checked.
-*If the port is to be used with a 802.1Q tag, uncheck '''Untagged''' and enter a VLAN ID.
+*If the port is to be used with an 802.1Q tag, uncheck '''Untagged''' and enter a VLAN ID.
 *Click '''Create'''
@@ Line 110: / Line 110: @@
 *Select 1 or more services to use for the IP interface (RTP and SIP).
 *Select the '''Host VLAN''' from which IP packets will exit.
-*Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
+*Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter an IP address, Netmask, and Gateway)
 *Enter an '''IP address'''
 *Enter a '''Netmask'''
@@ Line 136: / Line 136: @@
 *Select 1 or more services to use for the IP interface (RTP and SIP).
 *Select the '''Host VLAN''' from which IP packets will exit.
-*Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
+*Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter an IP address, Netmask, and Gateway)
 *Enter an '''IP address'''
 *Enter a '''Netmask'''
@@ Line 217: / Line 217: @@
 =SIP NAP=
-A Network Access Point or NAP represents the entry point to another network or destination peer (e.g. SIP proxy,SIP trunk, etc)
+A Network Access Point or NAP represents the entry point to another network or destination peer (e.g. SIP proxy, SIP trunk, etc)
 ==SIP NAP Configuration for Wide Area Network==
@@ Line 331: / Line 331: @@
 ==Access Control List==
-FreeSBC will automaticaly create Access Control List for each NAP you created.
+ProSBC will automatically create Access Control List for each NAP you created.
 [[Image:SIP_Access_Control_List_1.png]]
-If you double click one of the created ACL, you will see FreeSBC only accept the calls if source IP is match. In this sample; the calls from 192.168.1.10 will aceppted only.
+If you double click one of the created ACL, you will see ProSBC only accept the calls if the source IP matches. In this sample; the calls from 192.168.1.10 will be accepted only.
@@ Line 369: / Line 369: @@
-- Verify that the '''"Route was successfully created"''' message appears, and that the new route is listed in the Routeset list
+- Verify that the '''" Route was successfully created"''' message appears and that the new route is listed in the Routeset list
 [[Image:Route_Trunk_to_Server_1.png]]
@@ Line 395: / Line 395: @@
-- Verify that the '''"Route was successfully created"''' message appears, and that the new route is listed in the Routeset list
+- Verify that the '''" Route was successfully created"''' message appears and that the new route is listed in the Route set list
 [[Image:Route_Server_to_Trunk_1.png]]
@@ Line 401: / Line 401: @@
 =Activating the Configuration=
-Changes made to the configuration of the FreeSBC units are stored in the OAM&P Configuration and Logging database. In order for changes to be used by the system, they must first be activated. This is done at the system level and accessed from the Navigation panel.
+Changes made to the configuration of the ProSBC units are stored in the OAM&P Configuration and Logging database. In order for changes to be used by the system, they must first be activated. This is done at the system level and accessed from the Navigation panel.
 Check the following link for activating the configuration;

@@ Line 10: / Line 10: @@
 ==Prerequisites==
-[[FreeSBC|FreeSbc]] devices must be installed as described in their respective [[Product_Installation|installation guides]].
+[[FreeSBC|FreeSBC]] devices must be installed as described in their respective [[Product_Installation_SBC|installation guides]].
 =IP Network Configuration=

← Older revision		Revision as of 09:08, 9 January 2019
Line 398:		Line 398:

	[[Image:Route_Server_to_Trunk_1.png]]		[[Image:Route_Server_to_Trunk_1.png]]
		+
		+	=Activating the Configuration=
		+
		+	Changes made to the configuration of the FreeSBC units are stored in the OAM&P Configuration and Logging database. In order for changes to be used by the system, they must first be activated. This is done at the system level and accessed from the Navigation panel.
		+
		+	Check the following link for activating the configuration;
		+
		+	[[Toolpack:Activating_the_Configuration_D]]

	=SBC Use Cases=		=SBC Use Cases=

@@ Line 336: / Line 336: @@
-If you double click one of the created ACL, you will see FreeSBC only accept the calls if source IP is match.In this sample; the calls from 192.168.1.10 will aceppted only.
+If you double click one of the created ACL, you will see FreeSBC only accept the calls if source IP is match. In this sample; the calls from 192.168.1.10 will aceppted only.
@@ Line 399: / Line 399: @@
 [[Image:Route_Server_to_Trunk_1.png]]
-==SBC Use Cases==
+=SBC Use Cases=
 [[Toolpack:Tsbc Use Cases A|SBC Use Cases]]
-==SBC Turorial Guide V3.0==
+=SBC Turorial Guide V3.0=
 [[Tmedia Tsig Tdev Tutorial Guide v3.0|Version 3.0]]
 [[Category:Revise on Major]]

@@ Line 400: / Line 400: @@
 ==SBC Use Cases==
-[[Toolpack:Tsbc Use Cases A|Toolpack:Tsbc Use Cases A]]
+[[Toolpack:Tsbc Use Cases A|SBC Use Cases]]
 ==SBC Turorial Guide V3.0==

← Older revision		Revision as of 06:25, 1 February 2018
Line 398:		Line 398:

	[[Image:Route_Server_to_Trunk_1.png]]		[[Image:Route_Server_to_Trunk_1.png]]
		+
		+	==SBC Use Cases==
		+	[[Use Cases Version v2.8\|Toolpack:Tsbc Use Cases A]]
		+
		+	==SBC Turorial Guide V3.0==
		+	[[Tmedia Tsig Tdev Tutorial Guide v3.0\|Version 3.0]]
		+

	[[Category:Revise on Major]]		[[Category:Revise on Major]]

@@ Line 6: / Line 6: @@
 =SIP Trunking Example=
-[[Image:SIP_TRUNK_EXAMPLE_1.png]]<br>
+[[Image:sip_trunking_sample_1.png]]<br>
 ==Prerequisites==