MTP2:Connection mode - Revision history

Ktrueman: clean up

2009-09-02T13:32:29Z

clean up

Cboulanger at 02:13, 2 September 2009

2009-09-02T02:13:12Z

Ktrueman: fixed errors

2009-08-27T18:28:23Z

fixed errors

Ktrueman: initial content

2009-08-14T19:47:35Z

initial content

New page

The 'Connection mode' parameter specifies the different modes of connection for a MTP2 link.

The following values are allowed:

{| class="wikitable" border="1"
! width="150" style="background:#efefef;" |Connection mode
! width="350" style="background:#efefef;" |Description
|-
| Normal|| MPT2 layer is used in conjunction with an above MTP3 layer
|-
| HSL||
MPT2 layer high speed link is used in conjunction with an above MTP3 layer
|}

'''NOTE:''' The HSL mode uses timeslots 1 to 31 for E1 and 1 to 24 for T1/J1 interfaces. In Normal mode, you pick and choose the timeslots that are required.

@@ Line 1: / Line 1: @@
-The 'Connection mode' parameter specifies the different modes of connection for a [[MTP2 Layer|MTP2]] link.
+The '''Connection mode''' parameter specifies the different modes of connection for a [[MTP2 Layer|MTP2]] link. The following values are allowed:
 {| class="wikitable" border="1"
@@ Line 8: / Line 6: @@
 ! width="350" style="background:#efefef;" |Description
 |-
-| Normal|| MTP2 link specifies the use of Nx64/56kbps mode (where N can vary to 1 to 16) with the underneath MTP1 (physical) layer
+| Normal|| MTP2 link specifies the use of Nx64/56kbps mode (where N can vary from 1 to 16) with the underneath [[MTP1 Layer|MTP1]] (physical) layer
 |-
-| HSL|| MTP2 high speed link (HSL) specifies the use of the whole trunk bandwidth as a single link with the underneath MTP1 (physical) layer
+| HSL|| MTP2 high speed link (HSL) specifies the use of the entire trunk bandwidth as a single link with the underneath MTP1 (physical) layer
 |}
 '''NOTE:''' The HSL mode uses timeslots 1 to 31 for E1 and 1 to 24 for T1/J1 interfaces. In Normal mode, you pick and choose the timeslots that will be part of the MTP2 link.

@@ Line 8: / Line 8: @@
 ! width="350" style="background:#efefef;" |Description
 |-
-| Normal|| MTP2 layer is used in conjunction with an above MTP3 layer
+| Normal|| MTP2 link specifies the use of Nx64/56kbps mode (where N can vary to 1 to 16) with the underneath MTP1 (physical) layer
 |-
-| HSL|| MTP2 layer high speed link (HSL) is used in conjunction with an above MTP3 layer
+| HSL|| MTP2 high speed link (HSL) specifies the use of the whole trunk bandwidth as a single link with the underneath MTP1 (physical) layer
 |}
-'''NOTE:''' The HSL mode uses timeslots 1 to 31 for E1 and 1 to 24 for T1/J1 interfaces. In Normal mode, you pick and choose the timeslots that are required.
+'''NOTE:''' The HSL mode uses timeslots 1 to 31 for E1 and 1 to 24 for T1/J1 interfaces. In Normal mode, you pick and choose the timeslots that will be part of the MTP2 link.