Modify Fax Relay Profile C - Revision history

Allyntree: /* List of Parameters */

2015-09-28T15:41:37Z

List of Parameters

Allyntree: /* List of Parameters */

2015-07-29T17:12:48Z

List of Parameters

Allyntree: /* List of Parameters */

2014-11-06T15:34:19Z

List of Parameters

Allyntree at 15:26, 6 November 2014

2014-11-06T15:26:47Z

Allyntree: 2.8 profile article

2014-11-06T15:25:59Z

2.8 profile article

New page

=== '''''Applies to version v2.7''''' ===

{{DISPLAYTITLE:Modifying FAX Relay Profile Settings}}
<br>

'''To configure FAX Relay settings, do the following:'''

<br>

1- Click '''Fax Relay''' in the Editing Profile window, to display the customizable options.

[[Image:ModifyVoipFaxRelay_0_A.png]]

2- Modify settings as required.

[[File:fax_modem_relay_nse.png]]

3- To configure NSE, check the '''Use NSE''' checkbox.

'''NOTE:'''

If NSE exchange is possible (negociated in the SDP), the switch to passthrough will happen in the RTP stream and no longer wiil occur with a SIP re-INVITE. This implementation of NSE currently only supports a switch to passthrough, which means that you can have NSE packets switching to T.38.

* Click '''Save'''

==List of Parameters==
Fax/Modem Relay
* [[Parameter: Fax Modem Relay: Enable Fax/Modem Relay|Fax Modem Relay:Enable Fax/Modem Relay]]
* [[Parameter: Fax Modem Relay: Detection Mode|Fax Modem Relay: Detection Mode]]
* [[Parameter: Fax Modem Relay: Relay Mode|Fax Modem Relay: Relay Mode]]
* [[Parameter: Fax Modem Relay: Modem vs. Fax distinction timeout|Fax Modem Relay: Modem vs. Fax distinction timeout]]
* [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration|Fax Modem Relay: Fax/Modem tones detection duration]]
* [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection|Fax Modem Relay: Enable early Fax/Modem tone detection]]
* [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone|Fax Modem Relay: Enable switching to FAX relay upon CNG tone]]
<br>
T.38 Parameters
* [[Parameter: T.38 Parameters: Use V.34| T.38 Parameters: Use V.34]]
* [[Parameter: T.38 Parameters: Maximum Bit Rate| T.38 Parameters: Maximum Bit Rate]]
* [[Parameter: T.38 Parameters: Fill Bit Removal| T.38 Parameters: Fill Bit Removal]]
* [[Parameter: T.38 Parameters: Redundancy Count| T.38 Parameters: Redundancy Count]]
* [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)| T.38 Parameters: Transmission level (-1dBm unit)]]
<br>
Fax/Modem Pass-through Parameters
* [[Parameter: Fax Modem Pass-Through Parameters: Detection Type| Fax Modem Pass-Through Parameters: Detection Type]]
* [[Parameter: Fax Modem Pass-Through Parameters: Codec| Fax Modem Pass-Through Parameters: Codec]]
* [[Parameter: Fax Modem Pass-Through Parameters: Jitter Buffer Depth| Fax Modem Pass-Through Parameters: Jitter Buffer Depth]]
* [[Parameter: Fax Modem Pass-Through Parameters: Use NSE| Fax Modem Pass-Through Parameters: Use NSE]]

@@ Line 27: / Line 27: @@
 ==List of Parameters==
 Fax/Modem Relay
-* [[Parameter: Fax Modem Relay: Enable Fax/Modem Relay|Fax Modem Relay:Enable Fax/Modem Relay]]
+* [[Parameter: Fax Modem Relay: Enable Fax/Modem Relay|Enable Fax/Modem Relay]]
-* [[Parameter: Fax Modem Relay: Detection Mode|Fax Modem Relay: Detection Mode]]
+* [[Parameter: Fax Modem Relay: Detection Mode|Detection Mode]]
-* [[Parameter: Fax Modem Relay: Relay Mode|Fax Modem Relay: Relay Mode]]
+* [[Parameter: Fax Modem Relay: Relay Mode|Relay Mode]]
-* [[Parameter: Fax Modem Relay: Modem vs. Fax distinction timeout|Fax Modem Relay: Modem vs. Fax distinction timeout]]
+* [[Parameter: Fax Modem Relay: Modem vs. Fax distinction timeout|Modem vs. Fax distinction timeout]]
-* [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration|Fax Modem Relay: Fax/Modem tones detection duration]]
+* [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration|Fax/Modem tones detection duration]]
-* [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection|Fax Modem Relay: Enable early Fax/Modem tone detection]]
+* [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection|Enable early Fax/Modem tone detection]]
-* [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone|Fax Modem Relay: Enable switching to FAX relay upon CNG tone]]
+* [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone|Enable switching to FAX relay upon CNG tone]]
-* [[Parameter: Fax Modem Relay: Switch to passthrough upon Bell ANS|Fax Modem Relay: Switch to passthrough upon Bell ANS]]
+* [[Parameter: Fax Modem Relay: Switch to passthrough upon Bell ANS|Switch to passthrough upon Bell ANS]]
 <br>
 T.38 Parameters
-* [[Parameter: T.38 Parameters: Use V.34| T.38 Parameters: Use V.34]]
+* [[Parameter: T.38 Parameters: Use V.34|Use V.34]]
-* [[Parameter: T.38 Parameters: Maximum Bit Rate| T.38 Parameters: Maximum Bit Rate]]
+* [[Parameter: T.38 Parameters: Maximum Bit Rate|Maximum Bit Rate]]
-* [[Parameter: T.38 Parameters: Fill Bit Removal| T.38 Parameters: Fill Bit Removal]]
+* [[Parameter: T.38 Parameters: Fill Bit Removal|Fill Bit Removal]]
-* [[Parameter: T.38 Parameters: Redundancy Count| T.38 Parameters: Redundancy Count]]
+* [[Parameter: T.38 Parameters: Redundancy Count|Redundancy Count]]
-* [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)| T.38 Parameters: Transmission level (-1dBm unit)]]
+* [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)|Transmission level (-1dBm unit)]]
 <br>
 Fax/Modem Pass-through Parameters
-* [[Parameter: Fax Modem Pass-Through Parameters: Detection Type| Fax Modem Pass-Through Parameters: Detection Type]]
+* [[Parameter: Fax Modem Pass-Through Parameters: Detection Type|Detection Type]]
-* [[Parameter: Fax Modem Pass-Through Parameters: Codec| Fax Modem Pass-Through Parameters: Codec]]
+* [[Parameter: Fax Modem Pass-Through Parameters: Codec|Codec]]
-* [[Parameter: Fax Modem Pass-Through Parameters: Jitter Buffer Depth| Fax Modem Pass-Through Parameters: Jitter Buffer Depth]]
+* [[Parameter: Fax Modem Pass-Through Parameters: Jitter Buffer Depth|Jitter Buffer Depth]]
-* [[Parameter: Fax Modem Pass-Through Parameters: Packet Duration| Fax Modem Pass-Through Parameters: Packet Duration]]
+* [[Parameter: Fax Modem Pass-Through Parameters: Packet Duration|Packet Duration]]
-* [[Parameter: Fax Modem Pass-Through Parameters: Use NSE| Fax Modem Pass-Through Parameters: Use NSE]]
+* [[Parameter: Fax Modem Pass-Through Parameters: Use NSE|Use NSE]]
-* [[Parameter: Fax Modem Pass-Through Parameters: Support V.152 VBD| Fax Modem Pass-Through Parameters: Support V.152 VBD]]
+* [[Parameter: Fax Modem Pass-Through Parameters: Support V.152 VBD|Support V.152 VBD]]
-* [[Parameter: Fax Modem Pass-Through Parameters: Force V.152 VBD| Fax Modem Pass-Through Parameters: Force V.152 VBD]]
+* [[Parameter: Fax Modem Pass-Through Parameters: Force V.152 VBD|Force V.152 VBD]]

@@ Line 1: / Line 1: @@
-=== '''''Applies to version v2.7''''' ===
+=== '''''Applies to version v2.8''''' ===
 {{DISPLAYTITLE:Modifying FAX Relay Profile Settings}}
@@ Line 10: / Line 10: @@
 - Click '''Fax Relay''' in the Editing Profile window, to display the customizable options.
-[[Image:ModifyVoipFaxRelay_0_A.png]]
+[[Image:ProfileVoipFaxRelay_0.png]]
 - Modify settings as required.
-[[File:fax_modem_relay_nse.png]]
+[[File:ProfileVoipFaxRelay_1.png]]
 - To configure NSE, check the '''Use NSE''' checkbox.