Modify Fax Relay Profile F - Revision history

Allyntree at 18:15, 25 November 2020

2020-11-25T18:15:34Z

Allyntree at 23:51, 17 August 2020

2020-08-17T23:51:36Z

Allyntree at 13:54, 1 May 2019

2019-05-01T13:54:25Z

Allyntree: /* List of Parameters */ added two parameters

2017-11-14T19:09:38Z

List of Parameters: added two parameters

Allyntree at 19:05, 14 November 2017

2017-11-14T19:05:10Z

Allyntree: Change screenshot and add missing parameters

2017-11-14T19:01:53Z

Change screenshot and add missing parameters

New page

=== '''''Applies to version v3.0''''' ===

{{DISPLAYTITLE:Modifying FAX Relay Profile Settings}}
<br>

'''To configure FAX Relay settings, do the following:'''

<br>

1- Click '''Fax Relay''' in the Editing Profile window, to display the customizable options.

[[Image:ProfileVoipFaxRelay_A_0.png]]

2- Modify settings as required.

[[File:ProfileVoipFaxRelay_1.png]]

3- To configure NSE, check the '''Use NSE''' checkbox.

'''NOTE:'''

If NSE exchange is possible (negociated in the SDP), the switch to passthrough will happen in the RTP stream and no longer wiil occur with a SIP re-INVITE. This implementation of NSE currently only supports a switch to passthrough, which means that you can have NSE packets switching to T.38.

* Click '''Save'''

==List of Parameters==
Fax/Modem Relay
* [[Parameter: Fax Modem Relay: Enable Fax/Modem Relay|Enable Fax/Modem Relay]]
* [[Parameter: Fax Modem Relay: Detection Mode|Detection Mode]]
* [[Parameter: Fax Modem Relay: Relay Mode|Relay Mode]]
* [[Parameter: Fax Modem Relay: Modem vs. Fax distinction timeout|Modem vs. Fax distinction timeout]]
* [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration|Fax/Modem tones detection duration]]
* [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection|Enable early Fax/Modem tone detection]]
* [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone|Enable switching to FAX relay upon CNG tone]]
* [[Parameter: Fax Modem Relay: Switch to passthrough upon Bell ANS|Switch to passthrough upon Bell ANS]]
<br>
T.38 Parameters
* [[Parameter: T.38 Parameters: Use V.34|Use V.34]]
* [[Parameter: T.38 Parameters: Maximum Bit Rate|Maximum Bit Rate]]
* [[Parameter: T.38 Parameters: Fill Bit Removal|Fill Bit Removal]]
* [[Parameter: T.38 Parameters: Redundancy Count|Redundancy Count]]
* [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)|Transmission level (-1dBm unit)]]
<br>
Fax/Modem Pass-through Parameters
* [[Parameter: Fax Modem Pass-Through Parameters: Detection Type|Detection Type]]
* [[Parameter: Fax Modem Pass-Through Parameters: Codec|Codec]]
* [[Parameter: Fax Modem Pass-Through Parameters: Jitter Buffer Depth|Jitter Buffer Depth]]
* [[Parameter: Fax Modem Pass-Through Parameters: Packet Duration|Packet Duration]]
* [[Parameter: Fax Modem Pass-Through Parameters: Use NSE|Use NSE]]
* [[Parameter: Fax Modem Pass-Through Parameters: Support V.152 VBD|Support V.152 VBD]]
* [[Parameter: Fax Modem Pass-Through Parameters: Force V.152 VBD|Force V.152 VBD]]

← Older revision		Revision as of 23:51, 17 August 2020
Line 1:		Line 1:
−	=== '''''Applies to version v3.0, v3.1''''' ===	+	=== '''''Applies to version v3.0, v3.1, v3.2''''' ===

	{{DISPLAYTITLE:Modifying FAX Relay Profile Settings}}		{{DISPLAYTITLE:Modifying FAX Relay Profile Settings}}

← Older revision		Revision as of 13:54, 1 May 2019
Line 1:		Line 1:
−	=== '''''Applies to version v3.0''''' ===	+	=== '''''Applies to version v3.0, v3.1''''' ===

	{{DISPLAYTITLE:Modifying FAX Relay Profile Settings}}		{{DISPLAYTITLE:Modifying FAX Relay Profile Settings}}

@@ Line 1: / Line 1: @@
 {{DISPLAYTITLE:Modifying FAX Relay Profile Settings}}
 <br>
 '''To configure FAX Relay settings, do the following:'''

@@ Line 33: / Line 33: @@
 * [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration|Fax/Modem tones detection duration]]
 * [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection|Enable early Fax/Modem tone detection]]
-* [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone|Enable switching to FAX relay upon CNG tone]]
+* [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone|Switch to FAX relay upon CNG tone]]
 * [[Parameter: Fax Modem Relay: Switch to passthrough upon Bell ANS|Switch to passthrough upon Bell ANS]]
 <br>
@@ Line 42: / Line 43: @@
 * [[Parameter: T.38 Parameters: Redundancy Count|Redundancy Count]]
 * [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)|Transmission level (-1dBm unit)]]
 <br>
 Fax/Modem Pass-through Parameters

@@ Line 15: / Line 15: @@
 - Modify settings as required.
-[[File:ProfileVoipFaxRelay_1.png]]
+[[File:ProfileVoipFaxRelay_1A.png]]
 - To configure NSE, check the '''Use NSE''' checkbox.