Parameter: Point Code - Revision history

Luc Morissette: Added redirect to Point_Code page

2014-10-01T17:51:04Z

Added redirect to Point_Code page

Sylvain Fontaine at 15:37, 11 May 2012

2012-05-11T15:37:49Z

Allyntree at 16:48, 23 August 2010

2010-08-23T16:48:34Z

Allyntree at 19:16, 4 August 2010

2010-08-04T19:16:21Z

Allyntree: Created page with 'The Point Code is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each me…'

2010-08-04T16:11:38Z

Created page with 'The Point Code is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each me…'

New page

The Point Code is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length|DPC Length]] chosen previously.

@@ Line 1: / Line 1: @@
-The [[Point Code]] parameter has a number of meanings, which vary depending on the context in which it appears.
+#REDIRECT[[Point_Code]]
-−
-==When Creating a Point Code==
-−
-The Point Code parameter is used to define a point code by assigning it numerical values.
-−
-Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length|DPC Length]] chosen previously.
-−
-==When Configuring an MTP3 Route==
-−
-The [[Point Code]] parameter is used to associate a peer SS7 [[SP]] ([[DPC]]) with the MTP3 route. Available point codes are chosen from a drop-down list.
-−
-[[Category:Parameters]]

@@ Line 1: / Line 1: @@
-The '''Point Code''' parameter has a number of meanings, which vary depending on the context in which it appears.
+The [[Point Code]] parameter has a number of meanings, which vary depending on the context in which it appears.
-−
 ==When Creating a Point Code==
-The Point Code parameter is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length|DPC Length]] chosen previously.
+The Point Code parameter is used to define a point code by assigning it numerical values.
 ==When Configuring an MTP3 Route==
-The Point Code parameter is used to associate a point code with the MTP3 route. Available point codes are chosen from a drop-down list.
+The [[Point Code]] parameter is used to associate a peer SS7 [[SP]] ([[DPC]]) with the MTP3 route. Available point codes are chosen from a drop-down list.
 [[Category:Parameters]]

← Older revision		Revision as of 16:48, 23 August 2010
Line 10:		Line 10:

	The Point Code parameter is used to associate a point code with the MTP3 route. Available point codes are chosen from a drop-down list.		The Point Code parameter is used to associate a point code with the MTP3 route. Available point codes are chosen from a drop-down list.
		+
		+	[[Category:Parameters]]

← Older revision		Revision as of 19:16, 4 August 2010
Line 1:		Line 1:
−	The Point Code is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length\|DPC Length]] chosen previously.	+	The '''Point Code''' parameter has a number of meanings, which vary depending on the context in which it appears.
		+
		+
		+	==When Creating a Point Code==
		+
		+	The Point Code parameter is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length\|DPC Length]] chosen previously.
		+
		+
		+	==When Configuring an MTP3 Route==
		+
		+	The Point Code parameter is used to associate a point code with the MTP3 route. Available point codes are chosen from a drop-down list.