T1, E1, and J1 interfaces - Revision history

Cbilodeau: add category

2011-02-04T14:18:51Z

add category

Allyntree at 21:10, 18 November 2009

2009-11-18T21:10:10Z

Allyntree: /* Using BITS ports for signaling */

2009-11-18T21:09:36Z

Using BITS ports for signaling

Allyntree: /* Using BITS ports for signaling */

2009-11-18T21:09:20Z

Using BITS ports for signaling

Allyntree at 21:08, 18 November 2009

2009-11-18T21:08:41Z

Ktrueman: initial content

2009-07-10T16:23:59Z

initial content

New page

The Tmedia [[TMG3200]] and Tdev [[TMP6400]] TDM hardware adapters for T1, E1, and J1 lines provide for up to 64 lines. It is important that you verify the TDM module installed in your Tmedia unit.

For each T1/E1/J1 line that the Tmedia unit will use, a line interface with a related line service is configured in a one-to-one relationship. The configuring of the line interface activates the hardware and the line service is configured to transport traffic and signaling payload. A conceptual image is shown below:

[[Image:T1-e1-j1-line-interfaces.jpg|550px]]

← Older revision		Revision as of 14:18, 4 February 2011
Line 9:		Line 9:
	Starting with release 2.3 of [[Toolpack]], it is possible to convert unused BITS ports into [[Signaling_Ports\|signaling ports]], with indices of 1 and 0 respectively, in order to recover a channel on the primary STM-1 connection.		Starting with release 2.3 of [[Toolpack]], it is possible to convert unused BITS ports into [[Signaling_Ports\|signaling ports]], with indices of 1 and 0 respectively, in order to recover a channel on the primary STM-1 connection.
	However, the converted ports will be used as trunks, and not as clocking sources.		However, the converted ports will be used as trunks, and not as clocking sources.
		+
		+	[[Category:RevisionV2]]

← Older revision		Revision as of 21:10, 18 November 2009
Line 5:		Line 5:

	[[Image:T1-e1-j1-line-interfaces.jpg\|550px]]		[[Image:T1-e1-j1-line-interfaces.jpg\|550px]]
		+
		+	== Using BITS ports for signaling ==
		+	Starting with release 2.3 of [[Toolpack]], it is possible to convert unused BITS ports into [[Signaling_Ports\|signaling ports]], with indices of 1 and 0 respectively, in order to recover a channel on the primary STM-1 connection.
		+	However, the converted ports will be used as trunks, and not as clocking sources.

← Older revision		Revision as of 21:09, 18 November 2009
Line 5:		Line 5:

	[[Image:T1-e1-j1-line-interfaces.jpg\|550px]]		[[Image:T1-e1-j1-line-interfaces.jpg\|550px]]
−
−	~~== Using BITS ports for signaling ==~~
−	Starting with release 2.3 of [[Toolpack]], it is possible to convert unused BITS ports into [[Signaling_Ports\|signaling ports]], with indices of 1 and 0 respectively, in order to recover a channel on the primary STM-1 connection.
−	~~However, the converted ports will be used as trunks, and not as clocking sources.~~

@@ Line 7: / Line 7: @@
 == Using BITS ports for signaling ==
-Starting with release 2.3 of [[Toolpack]], it is possible to convert unused BITS ports into [[Signaling_Ports|signaling ports]] in order to recover a channel on the primary STM-1 connection.
+Starting with release 2.3 of [[Toolpack]], it is possible to convert unused BITS ports into [[Signaling_Ports|signaling ports]], with indices of 1 and 0 respectively, in order to recover a channel on the primary STM-1 connection.
 However, the converted ports will be used as trunks, and not as clocking sources.

← Older revision		Revision as of 21:08, 18 November 2009
Line 5:		Line 5:

	[[Image:T1-e1-j1-line-interfaces.jpg\|550px]]		[[Image:T1-e1-j1-line-interfaces.jpg\|550px]]
		+
		+	== Using BITS ports for signaling ==
		+	Starting with release 2.3 of [[Toolpack]], it is possible to convert unused BITS ports into [[Signaling_Ports\|signaling ports]] in order to recover a channel on the primary STM-1 connection.
		+	However, the converted ports will be used as trunks, and not as clocking sources.