Toolpack:Adding M2PA Links A - Revision history

Luc Morissette: Updated IP header TOS link

2016-10-31T15:15:29Z

Updated IP header TOS link

2013-07-15T14:59:55Z

2012-07-09T18:43:57Z

2012-06-07T22:09:50Z

2012-06-07T22:09:16Z

2010-08-06T20:22:24Z

2010-07-15T16:36:35Z

2010-06-30T19:11:16Z

2010-06-30T19:10:53Z

2010-06-30T19:10:21Z

@@ Line 44: / Line 44: @@
 * [[Parameter: Protocol Type|Protocol Type]]
 * [[Parameter: Number of SCTP Streams|Number of SCTP Streams]]
-* [[Parameter: IP Header TOS|IP Header TOS]]
+* [[Parameter:_Packet_Network:_Type_of_Service|IP Header TOS]]
 * [[Parameter: Destination Port|Destination Port]]

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.5, v2.6.''''' ===
+=== '''''Applies to version(s): v2.5, v2.6., v2.7''''' ===
 {{DISPLAYTITLE:Adding M2PA Links}}
 Now that you have created an M2PA service access point (SAP), you must create a new M2PA link. This can be done from the M2PA SAP configuration window.

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.5, v2.6.''''' ===
-{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
+{{DISPLAYTITLE:Adding M2PA Links}}
 Now that you have created an M2PA service access point (SAP), you must create a new M2PA link. This can be done from the M2PA SAP configuration window.
 To create an M2PA link:

← Older revision		Revision as of 22:09, 7 June 2012
Line 1:		Line 1:
		+	=== '''''Applies to version(s): v2.5, v2.6.''''' ===
		+	{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
	Now that you have created an M2PA service access point (SAP), you must create a new M2PA link. This can be done from the M2PA SAP configuration window.		Now that you have created an M2PA service access point (SAP), you must create a new M2PA link. This can be done from the M2PA SAP configuration window.
	To create an M2PA link:		To create an M2PA link:

← Older revision		Revision as of 20:22, 6 August 2010
Line 35:		Line 35:

	[[Image:Toolpack_v2.5_M2PA_Link_Address_2.png]]		[[Image:Toolpack_v2.5_M2PA_Link_Address_2.png]]
		+
		+
		+	==List of Parameters==
		+
		+	* [[Parameter: Name\|Name]]
		+	* [[Parameter: Protocol Type\|Protocol Type]]
		+	* [[Parameter: Number of SCTP Streams\|Number of SCTP Streams]]
		+	* [[Parameter: IP Header TOS\|IP Header TOS]]
		+	* [[Parameter: Destination Port\|Destination Port]]

@@ Line 1: / Line 1: @@
 Now that you have created an M2PA service access point (SAP), you must create a new M2PA link. This can be done from the M2PA SAP configuration window.
 To create an M2PA link:
 - Click '''Create new M2pa link''' in the M2PA SAP configuration window:
@@ Line 31: / Line 32: @@
-- Verify that the address has been added to the list, and that the '''<i>(your address)</i> was successfully added''' message appears (ex.: here the address is 190.0.0.0)
+- Verify that the address has been added to the list, and that the '''"<i>(your address)</i> was successfully added"''' message appears (ex.: here the address is 190.0.0.0)
 [[Image:Toolpack_v2.5_M2PA_Link_Address_2.png]]

@@ Line 19: / Line 19: @@
 ** '''Destination port''' (same value as the one configured on the destination side)
 * Click '''Create'''
 [[Image:Toolpack_v2.5_Creating_M2PA_Link.png]]

@@ Line 5: / Line 5: @@
 [[Image:Toolpack_v2.5_Create_M2PA_Link.png]]
 - Configure the new link:
@@ Line 27: / Line 28: @@
 [[Image:Toolpack_v2.5_M2PA_Link_Address.png]]
 - Verify that the address has been added to the list, and that the '''<i>(your address)</i> was successfully added''' message appears (ex.: here the address is 190.0.0.0)
 [[Image:Toolpack_v2.5_M2PA_Link_Address_2.png]]