Toolpack:Adding M2PA Links B - Revision history

Luc Morissette: Updated IP header TOS link

2016-10-31T15:15:55Z

Updated IP header TOS link

Allyntree: /* Applies to version(s): v2.8 */

2014-09-18T15:27:00Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-18T15:26:04Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-18T15:25:41Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-18T15:25:32Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-18T15:24:18Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-18T15:23:59Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-18T15:22:48Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-18T15:14:35Z

Applies to version(s): v2.8

Allyntree: New 2.8 article

2014-09-18T15:13:22Z

New 2.8 article

New page

=== '''''Applies to version(s): v2.8''''' ===
{{DISPLAYTITLE:Adding M2PA Links}}
AFter you create an M2PA service access point (SAP), you must create a new M2PA link. This can be done from the M2PA SAP configuration window.
To create an M2PA link:

1- Click '''Create new M2pa link''' in the M2PA SAP configuration window:

[[Image:Create_M2PA_0.png]]

2- Click '''Create new M2pa link''' in the M2PA SAP configuration window:

[[Image:Select_M2PA_0.png]]

3- Click '''Create new M2pa link''' in the M2PA SAP configuration window:

[[Image:Create_M2PA_Link_0.png]]

4- Configure the new link:

* Enter a '''name''' for the link
* Select a '''protocol type''':
** [[ITU]]
** [[ANSI]]
** [[TTC]]
* Set other features, as needed:
** Number of '''SCTP Streams'''
** '''IP Header [[TOS]]'''
** '''Destination port''' (same value as the one configured on the destination side)
* Click '''Create'''

[[Image:Create_M2PA_Link_1.png]]

5- Enter a '''destination address''' in the appropriate box in the information panel:

* Click the '''"<<"''' button to add the destination address to the address list

[[Image:Create_M2PA_Link_2.png]]

6- Verify that the address has been added to the list, and that the '''"<i>(your address)</i> was successfully added"''' message appears (ex.: here the address is 190.0.0.0)

[[Image:Create_M2PA_Link_3.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Protocol Type|Protocol Type]]
* [[Parameter: Number of SCTP Streams|Number of SCTP Streams]]
* [[Parameter: IP Header TOS|IP Header TOS]]
* [[Parameter: Destination Port|Destination Port]]

← Older revision		Revision as of 15:26, 18 September 2014
Line 11:		Line 11:


−	2- Select an M2PA ~~link~~:	+	2- Select an M2PA SAP:

	[[Image:SelectM2paLink_0.png]]		[[Image:SelectM2paLink_0.png]]

← Older revision		Revision as of 15:25, 18 September 2014
Line 11:		Line 11:


−	2- ~~Selecy~~ an M2PA link:	+	2- Select an M2PA link:

	[[Image:SelectM2paLink_0.png]]		[[Image:SelectM2paLink_0.png]]

@@ Line 6: / Line 6: @@
-- Click '''Create new M2pa link''' in the M2PA SAP configuration window:
+- Click '''M2PA''' in the navigation panel:
 [[Image:CreateM2pa_0.png]]
-- Click '''Create new M2pa link''' in the M2PA SAP configuration window:
+- Selecy an M2PA link:
 [[Image:SelectM2paLink_0.png]]

← Older revision		Revision as of 15:22, 18 September 2014
Line 13:		Line 13:
	2- Click '''Create new M2pa link''' in the M2PA SAP configuration window:		2- Click '''Create new M2pa link''' in the M2PA SAP configuration window:

−	[[Image:~~SelectM2pa_0~~.png]]	+	[[Image:SelectM2paLink_0.png]]

@@ Line 53: / Line 53: @@
 * [[Parameter: Protocol Type|Protocol Type]]
 * [[Parameter: Number of SCTP Streams|Number of SCTP Streams]]
-* [[Parameter: IP Header TOS|IP Header TOS]]
+* [[Parameter:_Packet_Network:_Type_of_Service|IP Header TOS]]
 * [[Parameter: Destination Port|Destination Port]]

@@ Line 29: / Line 29: @@
 ** [[TTC]]
 * Set other features, as needed:
 ** '''Destination port''' (same value as the one configured on the destination side)
 * Click '''Create'''

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.8''''' ===
 {{DISPLAYTITLE:Adding M2PA Links}}
-After you create an M2PA service access point (SAP), you must create a new M2PA link. This can be done from the M2PA SAP configuration window.
+After you create an M2PA service access point (SAP), you must create a new M2PA link. This is done from the M2PA SAP configuration window.
 To create an M2PA link:

@@ Line 8: / Line 8: @@
 - Click '''Create new M2pa link''' in the M2PA SAP configuration window:
-[[Image:Create_M2PA_0.png]]
+[[Image:CreateM2pa_0.png]]
 - Click '''Create new M2pa link''' in the M2PA SAP configuration window:
-[[Image:Select_M2PA_0.png]]
+[[Image:SelectM2pa_0.png]]
@@ Line 48: / Line 48: @@
 [[Image:Create_M2PA_Link_3.png]]
 ==List of Parameters==