Toolpack:Configuring Vlan SBC A - Revision history

Allyntree at 13:13, 15 December 2020

2020-12-15T13:13:03Z

2019-03-26T14:30:26Z

2019-03-26T14:30:09Z

List of Parameters: Added parameters

2019-03-26T14:28:59Z

Important Note

2019-03-22T17:12:14Z

To configure a VLAN

2018-12-12T17:21:15Z

Updated to specify the vlan ID 4095

2018-02-27T20:53:29Z

2018-02-25T22:01:11Z

To configure a VLAN

2017-10-23T19:19:27Z

To configure a VLAN

2017-10-23T18:17:16Z

← Older revision		Revision as of 13:13, 15 December 2020
Line 1:		Line 1:
−	~~=== '''''Applies to version(s): v3.0, v3.1''''' ===~~
	{{DISPLAYTITLE:Configuring a VLAN}}		{{DISPLAYTITLE:Configuring a VLAN}}
		+
		+	{\| class="wikitable"
		+	\|-
		+	\|rowspan="2"\|This article applies to:
		+	\|'''Product'''
		+	\|'''Version'''
		+	\|-
		+	\|SBC
		+	\|3.1
		+	\|}

	After you create a virtual port, you must create a new VLAN.		After you create a virtual port, you must create a new VLAN.

← Older revision		Revision as of 14:30, 26 March 2019
Line 1:		Line 1:
−	=== '''''Applies to version(s): v3.0''''' ===	+	=== '''''Applies to version(s): v3.0, v3.1''''' ===
	{{DISPLAYTITLE:Configuring a VLAN}}		{{DISPLAYTITLE:Configuring a VLAN}}

← Older revision		Revision as of 14:30, 26 March 2019
Line 53:		Line 53:
	* [[Parameter: Untagged\|Untagged]]		* [[Parameter: Untagged\|Untagged]]
	* [[Parameter: VLAN id\|VLAN id]]		* [[Parameter: VLAN id\|VLAN id]]
		+	* [[Parameter: Allow ICMP\|Allow ICMP]]
		+	* [[Parameter: Allow IP fragmentation\|Allow IP fragmentation]]

@@ Line 34: / Line 34: @@
 Please check here: [[TSBC-SW:Cloud:VMware_Adding_Network_Intefaces_A|How to add VMware Network Interfaces]]<br>
 <br>
-If VLANs must be configured follow these steps:<br>
+If VLANs must be configured, follow these steps:<br>
 *Enter a name for the VLAN
 *If the port is to be used untagged, make sure '''Untagged''' is checked.

@@ Line 17: / Line 17: @@
 [[Image:Create Vlan Interface_Tsbc_1.png]]<br><br>
 . Create a VLAN that uses this virtual port
 *Click '''Create new Host VLAN'''
 [[Image:Create Vlan Interface_Tsbc_2.png]]<br><br>
 . Configure the new VLAN
 ====Important Note====
 Vlans can be configured on the SBC in these cases:<br>

@@ Line 25: / Line 25: @@
 ====Important Note====
 Vlans can be configured on the SBC in these cases:<br>
-* Baremetal installation<br>
+* Baremetal installation
-* VMware installation with Passthrough or SR-IOV network interfaces<br>
+* VMware installation with Passthrough or SR-IOV network interfaces
 <br>
 Vlans should '''not''' be configured on the SBC in this case:<br>
-* VMware installation with E1000 or VMXNET 3 network interfaces<br>
+* VMware installation with network interfaces using vlans from 1 to 4094
-All interfaces on the SBC should be configured as untagged. Vlans are configured in the VMware port Groups. Please check here: [[TSBC-SW:Cloud:VMware_Adding_Network_Intefaces_A|How to add VMware Network Interfaces]]<br>
+In this case, all interfaces on the SBC should be configured as untagged. Vlans are configured in the VMware port Groups. <br>
 <br>
 If VLANs must be configured follow these steps:<br>

@@ Line 15: / Line 15: @@
 *Select a Virtual Port
-[[New image needed]]<br><br>
+[[Image:Create Vlan Interface_Tsbc_1.png]]<br><br>
 . Create a VLAN that uses this virtual port
 *Click '''Create new Host VLAN'''
-[[New image needed]]<br><br>
+[[Image:Create Vlan Interface_Tsbc_2.png]]<br><br>
 . Configure the new VLAN
@@ Line 29: / Line 29: @@
 *Click '''Create'''
-[[new image needed]] <br><br>
+[[Image:Create Vlan Interface_Tsbc_3.png]] <br><br>
 ==List of Parameters==

@@ Line 10: / Line 10: @@
 . Select '''IP Interfaces''' from the navigation panel
-[[Image:Create Voip Interface_Tsbc0.png]] <br><br>
+[[Image:Create Vlan Interface_Tsbc_0.png]] <br><br>
 . Click the '''Virtual Ports''' tab.