Toolpack:Configuring VoIP Interfaces E - Revision history

Allyntree at 13:36, 15 December 2020

2020-12-15T13:36:25Z

Allyntree at 17:38, 24 April 2019

2019-04-24T17:38:38Z

Allyntree: /* To configure a VoIP0 or VoIP1 port */

2017-10-24T18:05:20Z

To configure a VoIP0 or VoIP1 port

Allyntree: added screenshots

2017-10-24T17:59:30Z

added screenshots

Manon Bélanger: Fix comment

2017-04-25T12:49:14Z

Fix comment

Manon Bélanger: First version

2017-04-20T13:38:50Z

First version

New page

=== '''''Applies to version(s): v3.0''''' ===
{{DISPLAYTITLE:Configuring VoIP Interfaces}}

The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:

*IP Address
*Netmask
*Gateway

 

== To configure a VoIP0 or VoIP1 port ==

1. Select '''IP Interfaces''' from the navigation panel:

[[New image needed - under Hardware Units]]

 2. Click the '''IP Interfaces''' tab.
*Click '''Create New IP Interface'''

[[Image:Voip_Interface_1a.png]]

 3. Configure the IP port:

*Enter a name for the interface
*Select a service to use for the IP inteface
*Select a '''Virtual port''' from which IP packets will exit.
*Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
*Enter an '''IP address'''
*Enter a '''Netmask'''
*Enter a '''gateway address'''
*Click '''Save'''

'''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. 

[[New image needed]]

 

4. The changes are displayed in the IP interfaces information panel:

[[New image needed]]

 

5. Activate the configuration

Systems -> Edit -> Activate

6. It is necessary to reboot the adapters if you are using the vlan from 3441 to 3450 only.

Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter

It will take about 1.5 minutes to restart the unit.

'''Note:''' in a 1+1 system, both units must be restarted.

== List of Parameters ==

*[[Parameter: Interface name|Interface name]]
*[[Parameter: Services to use|Services to use]]
*[[Parameter: Virtual port|Virtual port]]
*[[Parameter: Use DHCP|Use dynamic IP]]
*[[Parameter: IP Address|IP Address]]
*[[Parameter: Netmask|Netmask]]
*[[Parameter: Gateway|Gateway]]

← Older revision		Revision as of 13:36, 15 December 2020
Line 1:		Line 1:
−	~~=== '''''Applies to version(s): v3.0, v3.1''''' ===~~
	{{DISPLAYTITLE:Configuring VoIP Interfaces}}		{{DISPLAYTITLE:Configuring VoIP Interfaces}}
		+
		+	{\| class="wikitable"
		+	\|-
		+	\|rowspan="2"\|This article applies to:
		+	\|'''Product'''
		+	\|'''Version'''
		+	\|-
		+	\|SBC
		+	\|3.0, 3.1
		+	\|}

	The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:		The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:

← Older revision		Revision as of 17:38, 24 April 2019
Line 1:		Line 1:
−	=== '''''Applies to version(s): v3.0''''' ===	+	=== '''''Applies to version(s): v3.0, v3.1''''' ===
	{{DISPLAYTITLE:Configuring VoIP Interfaces}}		{{DISPLAYTITLE:Configuring VoIP Interfaces}}

@@ Line 14: / Line 14: @@
 . Select '''IP Interfaces''' from the navigation panel:
-[[New image needed - under Hardware Units]]
+[[Image:CreateIpInterface_Tsbc_1.png]]
 <br> 2. Click the '''IP Interfaces''' tab.
@@ Line 34: / Line 34: @@
 '''Note:''' IP addresses using different virtual ports must be on different subnets. <br>
-[[New image needed]]
+[[Image:CreateIpInterface_Tsbc_1a.png]]
 <br>
@@ Line 40: / Line 40: @@
 . The changes are displayed in the IP interfaces information panel:
-[[New image needed]]
+[[Image:CreateIpInterface_Tsbc_1b.png]]
@@ Line 58: / Line 58: @@
 '''Note:''' in a 1+1 system, both units must be restarted.
 == List of Parameters ==

@@ Line 32: / Line 32: @@
 *Click '''Save'''
-'''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. <br>
+'''Note:''' IP addresses using different virtual ports must be on different subnets. <br>
 [[New image needed]]

@@ Line 46: / Line 46: @@
 . Activate the configuration
+. You must reboot the adapters only if you are using the vlan from ports 3441 to 3450.
+*Status -&gt;&nbsp;Adapters -&gt; Click on the adapter Serial Number -&gt; Reboot adapter
-. It is necessary to reboot the adapters if you are using the vlan from 3441 to 3450 only.
-−
 Status -&gt;&nbsp;Adapters -&gt; Click on the adapter Serial Number -&gt; Reboot adapter
 It will take about 1.5 minutes to restart the unit.
 == List of Parameters ==