Toolpack:Creating SS7 Point Codes A - Revision history

Allyntree at 18:34, 9 July 2012

2012-07-09T18:34:02Z

Allyntree: moved Toolpack v2.5:Creating SS7 Point Codes to Toolpack:Creating SS7 Point Codes A: New naming convention

2012-06-06T18:46:25Z

moved Toolpack v2.5:Creating SS7 Point Codes to Toolpack:Creating SS7 Point Codes A: New naming convention

Allyntree at 18:46, 6 June 2012

2012-06-06T18:46:01Z

Allyntree at 16:04, 4 August 2010

2010-08-04T16:04:47Z

Allyntree at 19:46, 14 July 2010

2010-07-14T19:46:54Z

Allyntree at 19:34, 30 June 2010

2010-06-30T19:34:39Z

Allyntree at 19:31, 30 June 2010

2010-06-30T19:31:11Z

Allyntree: Created page with 'To create SS7 originating and destination point codes: 1- Click '''Point Codes''' in the navigation panel Image:Toolpack_v2.5_Navigation_Panel_Point_Codes.png 2- Click '''…'

2010-06-30T19:20:12Z

Created page with 'To create SS7 originating and destination point codes: 1- Click '''Point Codes''' in the navigation panel Image:Toolpack_v2.5_Navigation_Panel_Point_Codes.png 2- Click '''…'

New page

To create SS7 originating and destination point codes:

1- Click '''Point Codes''' in the navigation panel

[[Image:Toolpack_v2.5_Navigation_Panel_Point_Codes.png]]

2- Click '''Create New Point Code'''

[[Image:Toolpack_v2.5_Create_Point_Code.png]]

3- Configure the new point code:

* Enter a '''name''' for the point code
* Select a point code '''type''' (select type-specific parameters)
* Select a point code '''length''' (14, 16, 24 bits)
* Enter a '''point code'''
* Click '''Create'''

In this example, an originating point code (OPC) was created.

[[Image:Toolpack_v2.5_Creating_Point_Code.png]]

4. Verify that the '''MTP3PointCode was successfully created''' message appears

[[Image:Toolpack_v2.5_Point_Code_Created.png]]

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.5, v2.6.''''' ===
-{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
+{{DISPLAYTITLE:Creating SS7 Point Codes}}
 Now that you have configured your MTP3 network, you must create point codes for your system. Point codes are used to define the Tmedia or Tdev system network, the adjacent network and the target network so that calls are properly routed from one network to the next.

← Older revision		Revision as of 18:46, 6 June 2012
Line 1:		Line 1:
		+	=== '''''Applies to version(s): v2.5, v2.6.''''' ===
		+	{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
	Now that you have configured your MTP3 network, you must create point codes for your system. Point codes are used to define the Tmedia or Tdev system network, the adjacent network and the target network so that calls are properly routed from one network to the next.		Now that you have configured your MTP3 network, you must create point codes for your system. Point codes are used to define the Tmedia or Tdev system network, the adjacent network and the target network so that calls are properly routed from one network to the next.

← Older revision		Revision as of 16:04, 4 August 2010
Line 27:		Line 27:

	[[Image:Toolpack_v2.5_Point_Code_Created.png]]		[[Image:Toolpack_v2.5_Point_Code_Created.png]]
		+
		+
		+	==List of parameters==
		+
		+	* [[Parameter: Name\|Name]]
		+	* [[Parameter: Type\|Type]]
		+	* [[Parameter: DPC Length\|DPC Length]]
		+	* [[Parameter: Point Code\|Point Code]]

@@ Line 1: / Line 1: @@
-To create SS7 originating and destination point codes:
+Now that you have configured your MTP3 network, you must create point codes for your system. Point codes are used to define the Tmedia or Tdev system network, the adjacent network and the target network so that calls are properly routed from one network to the next.
 - Click '''Point Codes''' in the navigation panel
@@ Line 21: / Line 24: @@
 [[Image:Toolpack_v2.5_Creating_Point_Code.png]]
-. Verify that the '''Mtp3PointCode was successfully created''' message appears, and the new point code appears in the '''Point Codes''' list
+. Verify that the '''"Mtp3PointCode was successfully created"''' message appears, and the new point code appears in the '''Point Codes''' list
 [[Image:Toolpack_v2.5_Point_Code_Created.png]]

@@ Line 21: / Line 21: @@
 [[Image:Toolpack_v2.5_Creating_Point_Code.png]]
-. Verify that the '''MTP3PointCode was successfully created''' message appears, and the new point code appears in the '''Point Codes''' list
+. Verify that the '''Mtp3PointCode was successfully created''' message appears, and the new point code appears in the '''Point Codes''' list
 [[Image:Toolpack_v2.5_Point_Code_Created.png]]