Toolpack:Creating SS7 Point Codes C - Revision history

Allyntree: /* Applies to version(s): v2.8. */ Revised step 3 and changed screenshot

2015-09-02T14:36:57Z

Applies to version(s): v2.8.: Revised step 3 and changed screenshot

Allyntree: /* Applies to version(s): v2.8. */

2015-06-23T15:06:51Z

Applies to version(s): v2.8.

Allyntree: Revised the introduction

2015-06-23T15:05:57Z

Revised the introduction

Allyntree at 13:05, 16 September 2014

2014-09-16T13:05:53Z

Allyntree: New 2.8 article

2014-09-16T13:03:30Z

New 2.8 article

New page

=== '''''Applies to version(s): v2.8.''''' ===
{{DISPLAYTITLE:Creating SS7 Point Codes}}
Once you have configured your MTP3 network, you must then create point codes for your system. Point codes are used to define the Tmedia or Tdev system network, the adjacent network and the target network so that calls are properly routed from one network to the next.

To create SS7 originating (OPC) and destination (DPC) point codes:

1- Click '''Point Codes''' in the navigation panel

[[Image:PointCodes_0_A.png]]

2- Click '''Create New Point Code'''

[[Image:PointCodes_1_A.png]]

3- Configure the new point code:

* Enter a '''name''' for the point code
* Select a point code '''type''' (select type-specific parameters)
* Select a point code '''length''' (14, 16, 24 bits)
* Enter a '''point code'''
* Click '''Create'''

In this example, an originating point code (OPC) is created.

[[Image:PointCodes_2_A.png]]

4. Verify that the '''"Mtp3PointCode was successfully created"''' message appears, and the new point code appears in the '''Point Codes''' list

[[Image:PointCodes_3_A.png]]

==List of parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Type|Type]]
* [[Parameter: DPC Length|DPC Length]]
* [[Parameter: Point Code|Point Code]]

@@ Line 18: / Line 18: @@
 * Select a point code '''type''' (select type-specific parameters)
 * Select a point code '''length''' (14, 16, 24 bits)
-* Enter a '''point code'''
+* Enter a '''point code'''. Either as bits, decimal, or hexadecimal.
 * Click '''Create'''

@@ Line 3: / Line 3: @@
 Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.
-To create SS7 originating (OPC) and destination (DPC) point codes:
+To create SS7 originating point codes (OPC) and destination point codes (DPC):
-−
 - Click '''Point Codes''' in the navigation panel
@@ Line 29: / Line 28: @@
 [[Image:PointCodes_3_A.png]]
 ==List of parameters==

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.8.''''' ===
 {{DISPLAYTITLE:Creating SS7 Point Codes}}
-Once you have configured your MTP3 network, you must then create point codes for your system. Point codes are used to define the Tmedia or Tdev system network, the adjacent network and the target network so that calls are properly routed from one network to the next.
+Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.
 To create SS7 originating (OPC) and destination (DPC) point codes:

@@ Line 26: / Line 26: @@
 [[Image:PointCodes_2_A.png]]
-. Verify that the '''"Mtp3PointCode was successfully created"''' message appears, and the new point code appears in the '''Point Codes''' list
+. Verify that the '''"PointCode was successfully created"''' message appears, and the new point code appears in the '''Point Codes''' list
 [[Image:PointCodes_3_A.png]]