Toolpack:Creating a 1+1 Group B - Revision history

Allyntree: /* Applies to version v2.8 */

2015-06-04T15:05:06Z

Applies to version v2.8

Allyntree: Formatting

2015-06-01T17:38:26Z

Formatting

Allyntree: Save -> Create

2015-06-01T17:34:08Z

Save -> Create

Allyntree: /* Applies to version v2.8 */

2015-01-20T15:40:20Z

Applies to version v2.8

Allyntree: Minor edits

2015-01-20T15:36:06Z

Minor edits

Allyntree: New Article: Place holder for 2.8

2014-08-25T12:57:22Z

New Article: Place holder for 2.8

New page

=== '''''Applies to version v2.8''''' ===
{{DISPLAYTITLE:Creating a 1+1 Group}}

A 1+1 group indentifies the two Tmedia hardware devices that will operate together to provide 1+1 backup protection. One device is identified as the primary hardware device, while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].

'''To create a 1+1 group:'''

1- Click '''1+1 Groups''' in the navigation panel

[[Image:Create1and1Group_0_B.png]]

2- Click '''Create New 1+1 Group'''

[[Image:Create1and1Group_1_B.png]]

3- Enter the serial numbers of the Primary and Backup Hardware devices.

* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)
* Select the '''serial number''' of the backup hardware device.
* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.
* Click '''Save'''

[[Image:Create1and1Group_2_B.png]]

4- Verify that the newly added 1+1 group appears in the '''1+1 Groups List'''

[[Image:Create1and1Group_3_B.png]]

← Older revision		Revision as of 15:05, 4 June 2015
Line 29:		Line 29:

	[[Image:Create1and1Group_3_B.png]]		[[Image:Create1and1Group_3_B.png]]
		+
		+	==List of Parameters==
		+
		+	* [[Parameter: Name\|Name]]
		+	* [[Parameter: Serial\|Serial]]
		+	* [[Parameter: Adapter Type\|Type]]
		+	* [[Parameter: Auto Switch-Back\|Auto Switch-Back]]

← Older revision		Revision as of 17:38, 1 June 2015
Line 26:		Line 26:


−	4- Verify that the newly added 1+1 group appears in the '''1+1 Groups ~~List~~'''	+	4- Verify that the newly added 1+1 group appears in the '''1+1 Groups''' list.

	[[Image:Create1and1Group_3_B.png]]		[[Image:Create1and1Group_3_B.png]]

@@ Line 21: / Line 21: @@
 * Select the '''serial number''' of the 1+1 backup hardware device.
 * Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.
-* Click '''Save'''
+* Click '''Create'''
 [[Image:Create1and1Group_2_B.png]]

@@ Line 2: / Line 2: @@
 {{DISPLAYTITLE:Creating a 1+1 Group}}
-A 1+1 group indentifies the two Tmedia hardware devices that will operate together to provide 1+1 backup protection. One device is identified as the primary hardware device, while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].
+A 1+1 group indentifies the two Tmedia hardware devices that operate together to provide 1+1 backup protection. One device is identified as the primary hardware device, while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].
 '''To create a 1+1 group:'''
-- Click '''1+1 Groups''' in the navigation panel
+- Click '''1+1''' in the navigation panel
 [[Image:Create1and1Group_0_B.png]]

@@ Line 7: / Line 7: @@
 - Click '''1+1 Groups''' in the navigation panel
 [[Image:Create1and1Group_0_B.png]]
@@ Line 13: / Line 12: @@
 - Click '''Create New 1+1 Group'''
 [[Image:Create1and1Group_1_B.png]]
-- Enter the serial numbers of the Primary and Backup Hardware devices.
+- Enter the serial numbers of the primary and 1+1 backup hardware devices.
+* Provide a name for the 1+1 group.
 * Select the '''serial number''' of the primary hardware device. (This field may already be filled.)
-* Select the '''serial number''' of the backup hardware device.
+* Select the '''serial number''' of the 1+1 backup hardware device.
 * Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.
 * Click '''Save'''
 [[Image:Create1and1Group_2_B.png]]
@@ Line 30: / Line 27: @@
 - Verify that the newly added 1+1 group appears in the '''1+1 Groups List'''
 [[Image:Create1and1Group_3_B.png]]