Toolpack:Creating a N+1 Group C - Revision history

Allyntree at 20:20, 24 November 2020

2020-11-24T20:20:53Z

Allyntree at 17:42, 27 July 2020

2020-07-27T17:42:09Z

Allyntree: /* Applies to version v2.9, v2.10 */

2017-10-24T19:34:21Z

Applies to version v2.9, v2.10

Allyntree: /* List of Parameters */

2017-03-30T18:38:25Z

List of Parameters

Allyntree: Added links for tooltips

2017-03-30T18:27:30Z

Added links for tooltips

Allyntree: revision change

2016-10-20T19:56:25Z

revision change

Allyntree: /* Applies to version v2.9 */

2015-11-10T16:08:04Z

Applies to version v2.9

Allyntree: Created page with "=== '''''Applies to version v2.9''''' === {{DISPLAYTITLE:Creating an N+1 Group}} Once the N+1 patch panel is created, you must configure an N+1 group and assign each hardware..."

2015-10-30T17:15:49Z

Created page with "=== '''''Applies to version v2.9''''' === {{DISPLAYTITLE:Creating an N+1 Group}} Once the N+1 patch panel is created, you must configure an N+1 group and assign each hardware..."

New page

=== '''''Applies to version v2.9''''' ===
{{DISPLAYTITLE:Creating an N+1 Group}}

Once the N+1 patch panel is created, you must configure an N+1 group and assign each hardware unit to their correct position on the N+1 pacth panel.

'''To create an N+1 Patch Panel:'''

1- Click '''N+1''' in the navigation panel

[[Image:N_Plus_One_0_A.png]]

2- Click '''Create New N+1 Group'''

[[Image:N_Plus_One_1_A.png]]

3- Set the correct serial numbers for units that are assigned as Primary and Secondary N+1 Patch panels, as well as the N+1 Backup unit.
*Configure the following:
**Primary N+1 Patch Panel: N+1 patch panel for the main fiber
**Secondary N+1 Patch Panel: N+1 patch panel for the APS
**N+1 Backup Unit: Standby unit
**Auto switch-back: Select this option to automatically switch TDM and VoIP media back to the original unit when it becomes available. If this option is not selected, then the backkup unit will remain active until it is manually rebooted.
**Port 0 to 14: Units must be listed as they are physically connected to the N+1 patch panel.
* Click '''Create'''

[[Image:N_Plus_One_2_A.png]]

4- Verify that the '''N+1 Group was successfully created''' message is displayed.

[[Image:N_Plus_One_3_A.png]]

<div class="mw-collapsible mw-collapsed" data-collapsetext="Northbound Interface" data-expandtext="Northbound Interface" style="width: 400px;">

'''Path'''
<pre>
</pre>

'''Parameters (text)'''
<pre>
</pre>

'''Parameters (json)'''
<pre>
</pre>
</div>

← Older revision		Revision as of 20:20, 24 November 2020
Line 1:		Line 1:
−	~~=== '''''Applies to version(s) v2.9, v2.10, v3.0, v3.2''''' ===~~
	{{DISPLAYTITLE:Creating an N+1 Group}}		{{DISPLAYTITLE:Creating an N+1 Group}}
		+	{\| class="wikitable"
		+	\|-
		+	\|rowspan="2"\|This article applies to:
		+	\|'''Product'''
		+	\|'''Version'''
		+	\|-
		+	\|Tmedia
		+	\|2.9, 2.10, 3.0, 3.2
		+	\|}

	Once the N+1 patch panel is created, you must configure an N+1 group and assign each hardware unit to their correct position on the N+1 pacth panel.		Once the N+1 patch panel is created, you must configure an N+1 group and assign each hardware unit to their correct position on the N+1 pacth panel.

← Older revision		Revision as of 19:34, 24 October 2017
Line 1:		Line 1:
−	=== '''''Applies to version v2.9, v2.10''''' ===	+	=== '''''Applies to version(s) v2.9, v2.10, v3.0''''' ===
	{{DISPLAYTITLE:Creating an N+1 Group}}		{{DISPLAYTITLE:Creating an N+1 Group}}

@@ Line 107: / Line 107: @@
 *[[Parameter: N+1 Backup Unit|N+1 Backup Unit]]
 *[[Parameter: Auto Switch-back|Auto Switch-back]]
-*[[Parameter: Port Numbers|Port Numbers]]
+*[[Parameter: Port Numbers|Ports 0-14]]

← Older revision		Revision as of 18:27, 30 March 2017
Line 99:		Line 99:
	</pre>		</pre>
	</div>		</div>
		+
		+	== List of Parameters ==
		+
		+	*[[Parameter: Name\|Name]]
		+	*[[Parameter: Primary N+1 Patch Panel\|Primary N+1 Patch Panel]]
		+	*[[Parameter: Secondary N+1 Patch Panel\|Secondary N+1 Patch Panel]]
		+	*[[Parameter: N+1 Backup Unit\|N+1 Backup Unit]]
		+	*[[Parameter: Auto Switch-back\|Auto Switch-back]]
		+	*[[Parameter: Port Numbers\|Port Numbers]]

← Older revision		Revision as of 19:56, 20 October 2016
Line 1:		Line 1:
−	=== '''''Applies to version v2.9''''' ===	+	=== '''''Applies to version v2.9, v2.10''''' ===
	{{DISPLAYTITLE:Creating an N+1 Group}}		{{DISPLAYTITLE:Creating an N+1 Group}}

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s) v2.9, v2.10, v3.0''''' ===
+=== '''''Applies to version(s) v2.9, v2.10, v3.0, v3.2''''' ===
 {{DISPLAYTITLE:Creating an N+1 Group}}
 Once the N+1 patch panel is created, you must configure an N+1 group and assign each hardware unit to their correct position on the N+1 pacth panel.
-'''To create an N+1 Patch Panel:'''
+'''To create an N+1 Group:'''
 - Click '''N+1''' in the navigation panel

@@ Line 37: / Line 37: @@
 '''Path'''
 <pre>
 </pre>
 '''Parameters (text)'''
 <pre>
 </pre>
 '''Parameters (json)'''
 <pre>
 </pre>
 </div>