Toolpack:Creating a NAP (SIGTRAN) C - Revision history

Allyntree: /* List of Parameters */ Added call-rate limiting parameter links

2015-09-28T15:48:10Z

List of Parameters: Added call-rate limiting parameter links

Allyntree at 13:56, 18 September 2014

2014-09-18T13:56:23Z

Allyntree: /* Applies to version(s): v2.8. */

2014-09-17T18:12:18Z

Applies to version(s): v2.8.

Allyntree: /* Applies to version(s): v2.8. */

2014-09-17T18:11:38Z

Applies to version(s): v2.8.

Allyntree: /* Applies to version(s): v2.8. */

2014-09-17T18:01:24Z

Applies to version(s): v2.8.

Allyntree: New article

2014-09-17T18:01:09Z

New article

New page

=== '''''Applies to version(s): v2.8.''''' ===
{{DISPLAYTITLE:Creating a NAP (ISUP)}}
A Network Access Point (NAP) represents the entry point to another network or destination peer.

After you have created an ISUP CIC group, you must create a network access point.

To create a network access point (NAP):

<br>
1- Click '''NAPs''' in the navigation panel

[[Image:CreateIsupNap_0.png]]

2- Click '''Create New NAP'''

[[Image:CreateIsupNap_1.png]]

3- Configure the new NAP:

*Enter a '''name''' for the NAP
*Select a '''user-created profile''', if not, select '''default'''
*Click '''Create'''

[[Image:CreateIsupNap_2.png]]

4- Verify that the '''NAP was successfully created''' message appears

[[Image:CreateIsupNap_3.png]]

5- Associate an ISUP interface with the NAP:

*Select an '''interface''' (the newly-created '''ISUP CIC group''')
*Click the '''"<<"''' button to add the interface to the list

[[Image:CreateIsupNap_4.png]]

'''The following screen is displayed:'''

[[Image:CreateIsupNap_5.png]]

*Select a value for [[Parameter:_Channel_Usage|'''Channel Usage''']], to avoid call collision
*Click '''Save'''

6- Verify that the '''"NAP was successfully updated"''' message appears

[[Image:CreateIsupNap_6.png]]

<br>

== List of Parameters ==

*[[Parameter: Name|Name]]
*[[Parameter: Default Profile|Default Profile]]
*[[Parameter: Channel Usage|Channel Usage]]

← Older revision		Revision as of 15:48, 28 September 2015
Line 59:		Line 59:
	*[[Parameter: Default Profile\|Default Profile]]		*[[Parameter: Default Profile\|Default Profile]]
	*[[Parameter: Channel Usage\|Channel Usage]]		*[[Parameter: Channel Usage\|Channel Usage]]
		+
		+
		+	'''Advanced Parameters-Call rate limiting'''
		+	*[[Parameter: Maximum calls per second\|Maximum calls per second]]
		+	*[[Parameter: Maximum call burst\|Maximum call burst]]
		+	*[[Parameter: Maximum simultaneous incoming calls\|Maximum simultaneous incoming calls]]
		+	*[[Parameter: Maximum simultaneous outgoing calls\|Maximum simultaneous outgoing calls]]
		+	*[[Parameter: Maximum simultaneous total calls\|Maximum simultaneous total calls]]
		+	*[[Parameter: Processing delay low threshold\|Processing delay low threshold]]
		+	*[[Parameter: Processing delay high threshold\|Processing delay high threshold]]

← Older revision		Revision as of 18:11, 17 September 2014
Line 40:		Line 40:


−	'''The following ~~screen~~ is displayed:'''	+	'''The following information is displayed:'''

	[[Image:CreateIsupNap_5.png]]		[[Image:CreateIsupNap_5.png]]

@@ Line 8: / Line 8: @@
 <br>
-- Click '''NAPs''' in the navigation pane
+- Click '''NAPs''' in the navigation panel
 [[Image:CreateIsupNap_0.png]]

@@ Line 46: / Line 46: @@
 *Select a value for [[Parameter:_Channel_Usage|'''Channel Usage''']], to avoid call collision
 *Click '''Save'''
 - Verify that the '''"NAP was successfully updated"''' message appears