Allyntree at 15:07, 29 December 2020

2020-12-29T15:07:09Z

Cbilodeau: create page for 3.1

2019-06-07T13:58:07Z

create page for 3.1

New page

=== '''''Applies to version(s): v3.1''''' ===

{{DISPLAYTITLE:Creating a SIP Domain}}
In a FreeSBC or Tmedia configuration, a "SIP Domain" represents a domain name to which users can register. It also defines registrars to which FreeSBC/Tmedia will forward registration requests.

The creation of SIP domains is performed as follows:

1. Select '''SIP Domain''' in the navigation panel

[[Image:Create_SIP_DomainNavMenu.png]]

2. Click '''Create New SIP Regisration Domain'''

[[Image:Create_SIP_Domain.png]]

3. Configure the SIP Registration Domain

[[Image:Create_SIP_Domain1.png]]

* Enter a configuration '''Name''' for this domain.
* Enter a '''Domain Name''' for the SIP Registration Domain. A domain can be a FQDN or an IP address.
* Set the number '''Maximum Registered Users''' for this domain
* Set the Expires value used by SBC when the remote device doesn't supply one ('''Default Contact Expiration''')
* Select '''Routing Method''' the system will use to route calls to registered users (if enabled in routing scripts).
** '''Register source''': Sends SIP Invite to the registering source IP address.
** '''Contact''': Sends SIP Invite to the 'contact' from the Register message.
* Set the '''Default Contact Expiration''', this value will be used when no ''Expires'' value is supplied by the user agent.
* Set the '''Minimum Contact Expiration''', this is the minimum ''Expires'' value that can be supplied by a user agent. Lower values will be rejected with a 423 'Interval too brief' response.
* Set the '''Maximum Contact Expiration''', this is the maximum ''Expires'' value that can be supplied by a user agent. Higher value are replaced by this parameter.
* Forwarding Parameters:
** Select the Registration '''Forwarding Mode''' to the registrar:
*** '''Contact Remapping''': Changes the user and the IP address.
*** '''Contact Passthrough''': Doesn't change anything. Enables devices to be contacted directly without going through the SBC.
** Set '''Minimum Registrar Expiration''', this is the minimum ''Expires'' value sent by the SBC to the registrar. If a user agent 'Expires' value is greater than this parameter, the SBC will do rate adaptation between the user agent and the Registrar.
** Set '''Maximum Pending Register Forward''', the maximum number of simultaneous pending register requests allowed for this domain. New REGISTER request are being refused passed this threshold.
** Set '''Maximum Simultaneous Register Forward''', the maximum number of simultaneous active register requests allowed for this domain. New REGISTER request are being refused passed this threshold.
** Select the Registration '''Registrar Selection Mode''' to the registrar:
*** '''Active/Standby''': The active registrar is the one with status up and the lowest priority (automatic fallback).
** Enable the '''Forward After Switchover''': After a switchover, the first register refresh request from each user will be forwarded to the active registrar.
* Click '''Create'''

4. Verify that the '''Sip registration domain was successfully created''' message appears

[[Image:Create_SIP_Domain2.png]]
<br><br>
[[Image:Create_SIP_Domain3.png]]

5. Create one or multiple SIP registrars for the SIP domain
* Click the SIP domain that was just created
* Click '''Create New SIP Registration Registrar'''

[[Image:Create_SIP_registrar.png]]

6. Enter the name of SIP Registration Registrar
* Select a NAP
* Click '''Create'''

[[Image:Sip5.png]]

'''Multiple registrars (registration redundancy)'''
Multiple registrars can be created per domain, for redundancy.
* Registrars are ordered by priority
* Users' registration requests are forwarded to the available registrar with the highest priority in the list
* SIP 'options' polling is used to determine which registrars are available or not

[[Image:multiple_registrars.png]]

'''Create routes for registered users'''

In most cases, FreeSBC will be required to route SIP calls (SIP Invite) to registered users. This is done by [[Sip_registration_forwarding#SIP_Calls_routing|creating appropriate routes]].

← Older revision		Revision as of 15:07, 29 December 2020
Line 1:		Line 1:
−	~~=== '''''Applies to version(s): v3.1''''' ===~~
−
	{{DISPLAYTITLE:Creating a SIP Domain}}		{{DISPLAYTITLE:Creating a SIP Domain}}
		+	{\| class="wikitable"
		+	\|-
		+	\|rowspan="3"\|This article applies to:
		+	\|'''Product'''
		+	\|'''Version'''
		+	\|-
		+	\|SBC
		+	\|3.1
		+	\|}
		+
	In a FreeSBC or Tmedia configuration, a "SIP Domain" represents a domain name to which users can register. It also defines registrars to which FreeSBC/Tmedia will forward registration requests.		In a FreeSBC or Tmedia configuration, a "SIP Domain" represents a domain name to which users can register. It also defines registrars to which FreeSBC/Tmedia will forward registration requests.

Toolpack:Creating a SIP Domain SBC B - Revision history

Allyntree at 15:07, 29 December 2020

Cbilodeau: create page for 3.1