Toolpack:Creating an ISUP Network B - Revision history

Allyntree: /* List of Parameters */ correction to the name of displayed parameter

2015-09-16T15:29:59Z

List of Parameters: correction to the name of displayed parameter

Allyntree at 14:00, 18 September 2014

2014-09-18T14:00:24Z

Allyntree: /* Applies to version(s): v2.8 */

2014-09-17T14:48:51Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-17T14:48:32Z

Applies to version(s): v2.8

Allyntree: /* Applies to version(s): v2.8 */

2014-09-17T14:47:40Z

Applies to version(s): v2.8

Allyntree: New 2.8 article

2014-09-17T14:39:42Z

New 2.8 article

New page

=== '''''Applies to version(s): v2.8''''' ===
{{DISPLAYTITLE:Creating an ISUP Network}}
AFter you create an ISUP stack, you must create a ISUP network.

The ISUP network communicates with the ISUP protocol layer about the collection of SS7 nodes that are accessible through MTP3 or M3UA.
Based upon your system configuration, one or more ISUP networks are created. Repeat this procedure for as many networks as you require.

'''NOTE:''' An ISUP network can be used by multiple ISUP interfaces even if they are members of different ISUP userpart; for example, to support multiple switch variants for a single SS7 network.

To create an ISUP network:
1- Click '''ISUP''' in the navigation pane.

[[Image:CreateIsupStack_0.png]]

2- Select the ISUP stack

[[Image:SelectIsupStack_0.png]]

3- Click "Create New ISUP Network" in the ISUP stack configuration window

[[Image:Create_ISUP_Network_0.png]]

4- Configure the new ISUP network:

* Enter a '''name''' for the network
* Select '''MTP3''' or '''M3UA''' as the '''type of network to bind'''
* Select a '''MTP3 network''' or a '''M3UA network'''
* Click '''Create'''

[[Image:Create_ISUP_Network_1.png]]

5- Verify that the '''"IsupNetwork was successfully created"''' message is displayed.

[[Image:Create_ISUP_Network_2.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Type of Network to Bind|Type of Network to Bind]]
* '''Depending on the type chosen:'''
** [[Parameter: MTP3 Network|MTP3 Network]]
** [[Parameter: M3UA Network|M3UA Network]]

← Older revision		Revision as of 14:48, 17 September 2014
Line 4:		Line 4:

	The ISUP network communicates with the ISUP protocol layer about the collection of SS7 nodes that are accessible through MTP3 or M3UA.		The ISUP network communicates with the ISUP protocol layer about the collection of SS7 nodes that are accessible through MTP3 or M3UA.
−	Based upon your system configuration, one or more ISUP networks ~~are created~~. Repeat this procedure for as many networks as you require.	+	Based upon your system configuration, you must create one or more ISUP networks. Repeat this procedure for as many networks as you require.

@@ Line 46: / Line 46: @@
 * '''Depending on the type chosen:'''
 ** [[Parameter: MTP3 Network|MTP3 Network]]
-** [[Parameter: M3UA Network|M3UA Network]]
+** [[Parameter: M3UA Network|M3UA Userpart]]

@@ Line 11: / Line 11: @@
 To create an ISUP network:
-- Click '''ISUP''' in the navigation pane.
+- Click '''ISUP''' in the navigation panel.
 [[Image:CreateIsupStack_0.png]]

← Older revision		Revision as of 14:48, 17 September 2014
Line 10:		Line 10:

	To create an ISUP network:		To create an ISUP network:
		+
	1- Click '''ISUP''' in the navigation pane.		1- Click '''ISUP''' in the navigation pane.

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.8''''' ===
 {{DISPLAYTITLE:Creating an ISUP Network}}
-AFter you create an ISUP stack, you must create a ISUP network.
+After you create an ISUP stack, you must create a ISUP network.
 The ISUP network communicates with the ISUP protocol layer about the collection of SS7 nodes that are accessible through MTP3 or M3UA.
@@ Line 38: / Line 38: @@
 [[Image:Create_ISUP_Network_2.png]]
 ==List of Parameters==