Toolpack:Creating an ISUP User Part B - Revision history

Allyntree: /* List of Parameters */

2015-09-17T14:57:03Z

List of Parameters

Allyntree: /* List of Parameters */

2015-09-17T14:22:50Z

List of Parameters

Allyntree: /* List of Parameters */

2015-09-16T15:42:56Z

List of Parameters

Allyntree at 14:00, 18 September 2014

2014-09-18T14:00:03Z

Allyntree: /* Applies to version(s): v2.8. */

2014-09-17T14:55:26Z

Applies to version(s): v2.8.

Allyntree: New 2.8 article

2014-09-17T14:54:09Z

New 2.8 article

New page

=== '''''Applies to version(s): v2.8.''''' ===
{{DISPLAYTITLE:Creating an ISUP User Part}}
Once you have created your ISUP network, you must create a new ISUP user part.

The user part is the container for the multiple [[ISUP]] interfaces. One user part is required for each protocol variant.

Multiple ISUP user parts can be instantiated within a single ISUP protocol layer. This allows a user application to interface with multiple [[SS7]] ISUP protocol variants at the same time. Only one ISUP user part is required for a specific variant as it can be assigned to multiple ISUP networks.

A user part can be seen as a protocol variant that a host application wants to use on the SS7 network.

To create an ISUP user part:

1- Click '''ISUP''' in the navigation pane.

[[Image:CreateIsupStack_0.png]]

2- Select the ISUP stack

[[Image:SelectIsupStack_0.png]]

3- Click '''Create New Isup Userpart''' in the ISUP stack configuration window:

[[Image:Create_ISUP_Userpart_0.png]]

4- Configure the new ISUP user part:

* Enter a '''name''' for the user part
* Select a '''protocol variant''' (depending on location)
* Select an '''MTP3 sub service field''' (the same that was previously set for MTP3)
* Select an '''address indicator type'''
* Select a '''[[Numbering Plan]]'''
* Click '''Create'''

[[Image:Create_ISUP_Userpart_1.png]]

5- Verify that the '''"IsupUserpart was successfully created"''' message appears

[[Image:Create_ISUP_Userpart_2.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Protocol Type|Protocol Variant]]
* [[Parameter: Sub Service Field|MTP3 Sub Service field]]
* [[Parameter: Default Nature of Address When Unspecified|Address Indicator Type]]
* [[Parameter: Default Numbering Plan When Unspecified|Numbering Plan]]

@@ Line 56: / Line 56: @@
 * [[Parameter: IsupUserPart_T1 Timer|T1 Timer]]
 * [[Parameter: IsupUserPart_T2 Timer|T2 Timer]]
-* [[Parameter: IsupUserPart_T5 Timer|T3 Timer]]
+* [[Parameter: IsupUserPart_T5 Timer|T5 Timer]]
 * [[Parameter: IsupUserPart_T6 Timer|T6 Timer]]
 * [[Parameter: IsupUserPart_T7 Timer|T7 Timer]]

← Older revision		Revision as of 15:42, 16 September 2015
Line 48:		Line 48:
	* [[Parameter: Default Nature of Address When Unspecified\|Address Indicator Type]]		* [[Parameter: Default Nature of Address When Unspecified\|Address Indicator Type]]
	* [[Parameter: Default Numbering Plan When Unspecified\|Numbering Plan]]		* [[Parameter: Default Numbering Plan When Unspecified\|Numbering Plan]]
		+
		+
		+	<div class="mw-collapsible mw-collapsed" data-collapsetext="Timers" data-expandtext="Timers" style="width: 400px;">
		+	{\| class="wikitable"
		+	\|-
		+
		+	* [[Parameter: IsupUserPart_T1 Timer\|T1 Timer]]
		+	* [[Parameter: IsupUserPart_T2 Timer\|T2 Timer]]
		+	* [[Parameter: IsupUserPart_T5 Timer\|T3 Timer]]
		+	* [[Parameter: IsupUserPart_T6 Timer\|T6 Timer]]
		+	* [[Parameter: IsupUserPart_T7 Timer\|T7 Timer]]
		+	* [[Parameter: IsupUserPart_T8 Timer\|T8 Timer]]
		+	* [[Parameter: IsupUserPart_T9 Timer\|T9 Timer]]
		+	* [[Parameter: IsupUserPart_T27 Timer\|T27 Timer]]
		+	* [[Parameter: IsupUserPart_T31 Timer\|T31 Timer]]
		+	* [[Parameter: IsupUserPart_T33 Timer\|T33 Timer]]
		+	* [[Parameter: IsupUserPart_T34 Timer\|T34 Timer]]
		+	* [[Parameter: IsupUserPart_T36 Timer\|T36 Timer]]
		+	* [[Parameter: Incoming Continuity Check timer\|Incoming Continuity Check timer]]
		+	* [[Parameter: Outgoing Continuity Check timer\|Outgoing Continuity Check timer]]
		+	* [[Parameter: Exit (EXM) timer\|Exit (EXM) timer]]
		+	* [[Parameter: Circuit reservation timer\|Circuit reservation timer]]
		+	* [[Parameter: Circuit reservation ack timer\|Circuit reservation ack timer]]
		+	* [[Parameter: Explicit Call Transfer timer\|Explicit Call Transfer timer]]
		+	* [[Parameter: Release response timer\|Release response timer]]
		+	* [[Parameter: Final release response timer\|Final release response timer]]
		+
		+	\|}
		+	</div>
		+
		+
		+	<div class="mw-collapsible mw-collapsed" data-collapsetext="Advanced Parameters" data-expandtext="Advanced Parameters" style="width: 400px;">
		+	{\| class="wikitable"
		+	\|-
		+	* [[Parameter: Cause Release Location\|Cause Release Location]]
		+	* [[Parameter: Send INR if no calling nb.in IAM\|Send INR if no calling nb.in IAM]]
		+	* [[Parameter: Call modification allowed\|Call modification allowed]]
		+	* [[Parameter: Max length of user-to-user info\|Max length of user-to-user info]]
		+	* [[Parameter: Allow pass on\|Allow pass on]]
		+	* [[Parameter: Allow group messages\|Allow group messages]]
		+	\|}
		+	</div>

@@ Line 46: / Line 46: @@
 * [[Parameter: Protocol Type|Protocol Variant]]
 * [[Parameter: Sub Service Field|MTP3 Sub Service field]]
-* [[Parameter: Default Nature of Address When Unspecified|Address Indicator Type]]
+* [[Parameter: Default Nature of Address When Unspecified|Default Nature of Address When Unspecified]]
-* [[Parameter: Default Numbering Plan When Unspecified|Numbering Plan]]
+* [[Parameter: Default Numbering Plan When Unspecified|Default Numbering Plan When Unspecified]]

@@ Line 10: / Line 10: @@
 To create an ISUP user part:
-- Click '''ISUP''' in the navigation pane.
+- Click '''ISUP''' in the navigation panel.
 [[Image:CreateIsupStack_0.png]]

@@ Line 3: / Line 3: @@
 Once you have created your ISUP network, you must create a new ISUP user part.
-The user part is the container for the multiple [[ISUP]] interfaces. One user part is required for each protocol variant.
+The user part is the container for the multiple [[ISUP]] interfaces. One user part is required for each protocol variant. A user part can be seen as a protocol variant that a host application wants to use on the SS7 network.
-Multiple ISUP user parts can be instantiated within a single ISUP protocol layer. This allows a user application to interface with multiple [[SS7]] ISUP protocol variants at the same time. Only one ISUP user part is required for a specific variant as it can be assigned to multiple ISUP networks.
+Multiple ISUP user parts can be instantiated within a single ISUP protocol layer. This allows a user application to interface with multiple [[SS7]] ISUP protocol variants at the same time. In addition, only one ISUP user part is required for a specific variant as it can be assigned to multiple ISUP networks.
 To create an ISUP user part:
@@ Line 41: / Line 40: @@
 [[Image:Create_ISUP_Userpart_2.png]]
 ==List of Parameters==