Toolpack:Creating an M3UA Configuration (IPSP) A - Revision history

Allyntree at 18:50, 9 July 2012

2012-07-09T18:50:23Z

Allyntree: moved Toolpack v2.5:Creating an M3UA Configuration (IPSP) to Toolpack:Creating an M3UA Configuration (IPSP) A: New naming convention

2012-06-07T22:31:39Z

moved Toolpack v2.5:Creating an M3UA Configuration (IPSP) to Toolpack:Creating an M3UA Configuration (IPSP) A: New naming convention

Allyntree at 22:31, 7 June 2012

2012-06-07T22:31:14Z

Allyntree at 17:14, 23 August 2010

2010-08-23T17:14:53Z

Allyntree at 17:15, 15 July 2010

2010-07-15T17:15:08Z

Allyntree at 16:30, 6 July 2010

2010-07-06T16:30:31Z

Allyntree: Created page with 'To create an M3UA configuration on IPSP: 1- Click '''M3UA''' in the navigation panel: Image:Toolpack_v2.5_Navigation_Panel_M3UA.png 2- Configure the M3UA service for IPSP:…'

2010-07-06T16:18:58Z

Created page with 'To create an M3UA configuration on IPSP: 1- Click '''M3UA''' in the navigation panel: Image:Toolpack_v2.5_Navigation_Panel_M3UA.png 2- Configure the M3UA service for IPSP:…'

New page

To create an M3UA configuration on IPSP:

1- Click '''M3UA''' in the navigation panel:

[[Image:Toolpack_v2.5_Navigation_Panel_M3UA.png]]

2- Configure the M3UA service for IPSP:

* Enter a '''name''' for the configuration
* Select '''IP Server Process (IPSP)''' as the node type
* Click '''Create'''

[[Image:Toolpack_v2.5_Creating_IPSP_M3UA_Configuration.png]]

3- Verify that the '''M3ua Cfg was successfully created''' message appears

[[Image:Toolpack_v2.5_IPSP_M3UA_Configuration_Created.png]]

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.5, v2.6.''''' ===
-{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
+{{DISPLAYTITLE:Creating an M3UA Configuration (IPSP)}}
 To set up your M3UA system on an IP server process (IPSP), you must first create a new M3UA configuration.
 In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This system is typically set up on two IP signaling points.

← Older revision		Revision as of 22:31, 7 June 2012
Line 1:		Line 1:
		+	=== '''''Applies to version(s): v2.5, v2.6.''''' ===
		+	{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
	To set up your M3UA system on an IP server process (IPSP), you must first create a new M3UA configuration.		To set up your M3UA system on an IP server process (IPSP), you must first create a new M3UA configuration.
	In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This system is typically set up on two IP signaling points.		In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This system is typically set up on two IP signaling points.

← Older revision		Revision as of 17:14, 23 August 2010
Line 20:		Line 20:

	[[Image:Toolpack_v2.5_M3UA_IPSP_Configuration_Created.png]]		[[Image:Toolpack_v2.5_M3UA_IPSP_Configuration_Created.png]]
		+
		+
		+	==List of Parameters==
		+
		+	* [[Parameter: Name\|Name]]
		+	* [[Parameter: Node Type\|Node Type]]

@@ Line 1: / Line 1: @@
 To create an M3UA configuration on IPSP:
 - Click '''M3UA''' in the navigation panel:
@@ Line 13: / Line 17: @@
 [[Image:Toolpack_v2.5_Creating_M3UA_IPSP_Configuration.png]]
-- Verify that the '''M3ua Cfg was successfully created''' message appears
+- Verify that the '''"M3ua Cfg was successfully created"''' message appears
 [[Image:Toolpack_v2.5_M3UA_IPSP_Configuration_Created.png]]

@@ Line 11: / Line 11: @@
 * Click '''Create'''
-[[Image:Toolpack_v2.5_Creating_IPSP_M3UA_Configuration.png]]
+[[Image:Toolpack_v2.5_Creating_M3UA_IPSP_Configuration.png]]
 - Verify that the '''M3ua Cfg was successfully created''' message appears
-[[Image:Toolpack_v2.5_IPSP_M3UA_Configuration_Created.png]]
+[[Image:Toolpack_v2.5_M3UA_IPSP_Configuration_Created.png]]