Toolpack:Creating an M3UA Configuration E - Revision history

Allyntree at 18:44, 9 December 2020

2020-12-09T18:44:23Z

Allyntree at 13:17, 26 August 2020

2020-08-26T13:17:59Z

Allyntree at 15:57, 20 December 2017

2017-12-20T15:57:24Z

Allyntree at 14:53, 4 November 2016

2016-11-04T14:53:54Z

Allyntree: Added northbound data

2016-01-11T16:22:38Z

Added northbound data

Allyntree: Created page with "=== '''''Applies to version(s): v2.9.''''' === {{DISPLAYTITLE:Creating an M3UA Configuration}} To set up your M3UA system on an IP server process (IPSP), you must first create..."

2015-12-03T14:45:22Z

Created page with "=== '''''Applies to version(s): v2.9.''''' === {{DISPLAYTITLE:Creating an M3UA Configuration}} To set up your M3UA system on an IP server process (IPSP), you must first create..."

New page

=== '''''Applies to version(s): v2.9.''''' ===
{{DISPLAYTITLE:Creating an M3UA Configuration}}
To set up your M3UA system on an IP server process (IPSP), you must first create a new M3UA configuration.
In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This system is typically set up on two IP signaling points.

To create an M3UA configuration on IPSP:

1- Click '''M3UA''' in the navigation panel:

[[Image:CreateM3ua_0.png]]

2- Configure the M3UA service for IPSP:

* Enter a '''name''' for the configuration
* Select '''IP Server Process (IPSP)''' as the node type
* Click '''Create'''

[[Image:CreateM3ua_1.png]]

3- Verify that the '''"M3ua Cfg was successfully created"''' message appears

[[Image:CreateM3ua_2.png]]

<div class="mw-collapsible mw-collapsed" data-collapsetext="Northbound Interface" data-expandtext="Northbound Interface" style="width: 400px;">

'''Path'''
<pre>
</pre>

'''Parameters (text)'''
<pre>
</pre>

'''Parameters (json)'''
<pre>
</pre>
</div>

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Node Type|Node Type]]
<br>
<div class="mw-collapsible mw-collapsed" data-collapsetext="Advanced Parameters" data-expandtext="Advanced Parameters" style="width: 400px;">
{| class="wikitable"
|-

* [[Parameter: M3UA: Only one hardware unit is active|Only one hardware unit is active]]
* [[Parameter: M3UA: Destination Restrict supported|Destination Restrict supported]]
* [[Parameter: M3UA: Congestion level 1|Congestion level 1]]
* [[Parameter: M3UA: Congestion level 2|Congestion level 2]]
* [[Parameter: M3UA: Congestion level 3|Congestion level 3]]
* [[Parameter: M3UA: Restart Timer|Restart Timer]]
* [[Parameter: M3UA: MTP3 Status Timer|MTP3 Status Timer]]
* [[Parameter: M3UA: AS Pending Timer|AS Pending Timer]]
* [[Parameter: M3UA: Heartbeat Timer|Heartbeat Timer]]
* [[Parameter: M3UA: ASP Up Timer|ASP Up Timer]]
* [[Parameter: M3UA: ASP Down Timer|ASP Down Timer]]
* [[Parameter: M3UA: ASP Messages Timeout|ASP Messages Timeout]]
* [[Parameter: M3UA: DAUD Timer|DAUD Timer]]
* [[Parameter: M3UA: DRKM Timer|DRKM Timer]]
* [[Parameter: M3UA: Number of DKRM messages|Number of DKRM messages]]
* [[Parameter: M3UA: DUNA Settle Timeout|DUNA Settle Timeout]]
* [[Parameter: M3UA: Sequence Control Timer|Sequence Control Timer]]

|}
</div>

@@ Line 1: / Line 1: @@
 {{DISPLAYTITLE:Creating an M3UA Configuration}}
 To set up a M3UA system on an IP server process (IPSP), you must create an M3UA configuration.
 In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. The system is typically set up on two IP signaling points.

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.9, v2.10, v3.0''''' ===
+=== '''''Applies to version(s): 2.9, 2.10, 3.0, 3.2''''' ===
 {{DISPLAYTITLE:Creating an M3UA Configuration}}
-To set up a M3UA system on an IP server process (IPSP), you must create a new M3UA configuration.
+To set up a M3UA system on an IP server process (IPSP), you must create an M3UA configuration.
 In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. The system is typically set up on two IP signaling points.

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.9, v2.10''''' ===
+=== '''''Applies to version(s): v2.9, v2.10, v3.0''''' ===
 {{DISPLAYTITLE:Creating an M3UA Configuration}}
-To set up your M3UA system on an IP server process (IPSP), you must first create a new M3UA configuration.
+To set up a M3UA system on an IP server process (IPSP), you must create a new M3UA configuration.
-In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This system is typically set up on two IP signaling points.
+In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. The system is typically set up on two IP signaling points.
 To create an M3UA configuration on IPSP:

@@ Line 30: / Line 30: @@
 '''Path'''
 <pre>
 </pre>
 '''Parameters (text)'''
 <pre>
 </pre>
 '''Parameters (json)'''
 <pre>
 </pre>
 </div>