Toolpack:Creating an M3UA Configuration SGP B - Revision history

Nicole Tan at 19:54, 2 June 2014

2014-06-02T19:54:22Z

Nicole Tan: /* Applies to version(s): v2.7. */

2014-05-28T15:57:27Z

Applies to version(s): v2.7.

Nicole Tan: Added configuration screen shot

2014-05-28T15:55:31Z

Added configuration screen shot

Nicole Tan: Decription about SGP

2014-05-28T15:48:01Z

Decription about SGP

Nicole Tan: Modified the page from IPSP to SGP

2014-05-28T14:15:59Z

Modified the page from IPSP to SGP

Nicole Tan: Initial the page

2014-05-27T19:30:36Z

Initial the page

New page

=== '''''Applies to version(s): v2.7.''''' ===
{{DISPLAYTITLE:Creating an M3UA Configuration (IPSP)}}
To set up your M3UA system on an IP server process (IPSP), you must first create a new M3UA configuration.
In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This system is typically set up on two IP signaling points.

To create an M3UA configuration on IPSP:

1- Click '''M3UA''' in the navigation panel:

[[Image:M3ua_0.png]]

2- Configure the M3UA service for IPSP:

* Enter a '''name''' for the configuration
* Select '''IP Server Process (IPSP)''' as the node type
* Click '''Create'''

[[Image:Toolpack_v2.5_Creating_M3UA_IPSP_Configuration.png]]

3- Verify that the '''"M3ua Cfg was successfully created"''' message appears

[[Image:Toolpack_v2.5_M3UA_IPSP_Configuration_Created.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Node Type|Node Type]]

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.7.''''' ===
-{{DISPLAYTITLE:Creating an M3UA Configuration - SGP}}
+{{DISPLAYTITLE:Creating an M3UA Configuration (SGP)}}
 To set up your M3UA system as a Signaling Gateway Process (SGP), you must first create a new M3UA configuration.

@@ Line 2: / Line 2: @@
 {{DISPLAYTITLE:Creating an M3UA Configuration - SGP}}
 To set up your M3UA system as a Signaling Gateway Process (SGP), you must first create a new M3UA configuration.
 In this configuration the the SIGTRAN M3UA is an extension of the MTP3 layer. This system is typically set up between Signaling Gateway Process (SGP) and Application Server Process .
@@ Line 22: / Line 23: @@
 [[Image:Toolpack_v2.5_M3UA_IPSP_Configuration_Created.png]]
 ==List of Parameters==

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.7.''''' ===
 {{DISPLAYTITLE:Creating an M3UA Configuration - SGP}}
-To set up your M3UA system on an IP server process (IPSP), you must first create a new M3UA configuration.
+To set up your M3UA system as a Signaling Gateway Process (SGP), you must first create a new M3UA configuration.
-In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This system is typically set up on two IP signaling points.
+In this configuration the the SIGTRAN M3UA is an extension of the MTP3 layer. This system is typically set up between Signaling Gateway Process (SGP) and Application Server Process .
-To create an M3UA configuration on IPSP:
+To create an M3UA SGP configuration:

@@ Line 17: / Line 17: @@
 * Click '''Create'''
-[[Image:Toolpack_v2.5_Creating_M3UA_IPSP_Configuration.png]]
+[[Image:Create_M3UA_SGP.jpg]]
 - Verify that the '''"M3ua Cfg was successfully created"''' message appears

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.7.''''' ===
-{{DISPLAYTITLE:Creating an M3UA Configuration (IPSP)}}
+{{DISPLAYTITLE:Creating an M3UA Configuration - SGP}}
 To set up your M3UA system on an IP server process (IPSP), you must first create a new M3UA configuration.
 In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This system is typically set up on two IP signaling points.
@@ Line 11: / Line 11: @@
 [[Image:M3ua_0.png]]
-- Configure the M3UA service for IPSP:
+- Configure the M3UA service for SGP:
 * Enter a '''name''' for the configuration
-* Select '''IP Server Process (IPSP)''' as the node type
+* Select '''Signaling Gateway Process (SGP)''' as the node type
 * Click '''Create'''