Toolpack:Creating an M3UA Configuration SGP C - Revision history

Allyntree at 18:26, 2 December 2015

2015-12-02T18:26:16Z

Allyntree: /* List of Parameters */

2015-06-23T15:22:23Z

List of Parameters

Allyntree: /* List of Parameters */

2015-06-23T15:21:04Z

List of Parameters

Allyntree: /* List of Parameters */

2015-06-23T15:20:47Z

List of Parameters

Allyntree: /* List of Parameters */ Added advanced parameter links

2015-06-23T15:20:23Z

List of Parameters: Added advanced parameter links

Allyntree: /* Applies to version(s): v2.7. */

2014-09-18T15:49:30Z

Applies to version(s): v2.7.

Allyntree: New 2.8 article

2014-09-18T15:47:38Z

New 2.8 article

New page

=== '''''Applies to version(s): v2.7.''''' ===
{{DISPLAYTITLE:Creating an M3UA Configuration (SGP)}}
To set up your M3UA system as a Signaling Gateway Process (SGP), you must first create a new M3UA configuration.

In this configuration the the SIGTRAN M3UA is an extension of the MTP3 layer. This system is typically set up between Signaling Gateway Process (SGP) and Application Server Process .

To create an M3UA SGP configuration:

1- Click '''M3UA''' in the navigation panel:

[[Image:CreateM3ua_0.png]]

2- Configure the M3UA service for SGP:

* Enter a '''name''' for the configuration
* Select '''Signaling Gateway Process (SGP)''' as the node type
* Click '''Create'''

[[Image:Create_M3UA_SGP.jpg]]

3- Verify that the '''"M3ua Cfg was successfully created"''' message appears

[[Image:CreateM3ua_2.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Node Type|Node Type]]

@@ Line 28: / Line 28: @@
 * [[Parameter: Name|Name]]
 * [[Parameter: Node Type|Node Type]]
+<br>
 <div class="mw-collapsible mw-collapsed" data-collapsetext="Advanced Parameters" data-expandtext="Advanced Parameters" style="width: 400px;">
 {| class="wikitable"
 |-
-<br><br>
-Advanced Parameters
 * [[Parameter: M3UA: Only one hardware unit is active|Only one hardware unit is active]]
 * [[Parameter: M3UA: Destination Restrict supported|Destination Restrict supported]]

@@ Line 32: / Line 32: @@
 {| class="wikitable"
 |-
-<br>
+<br><br>
 Advanced Parameters
 * [[Parameter: M3UA: Only one hardware unit is active|Only one hardware unit is active]]

@@ Line 32: / Line 32: @@
 {| class="wikitable"
 |-
 Advanced Parameters
 * [[Parameter: M3UA: Only one hardware unit is active|Only one hardware unit is active]]

← Older revision		Revision as of 15:20, 23 June 2015
Line 28:		Line 28:
	* [[Parameter: Name\|Name]]		* [[Parameter: Name\|Name]]
	* [[Parameter: Node Type\|Node Type]]		* [[Parameter: Node Type\|Node Type]]
		+
		+	<div class="mw-collapsible mw-collapsed" data-collapsetext="Advanced Parameters" data-expandtext="Advanced Parameters" style="width: 400px;">
		+	{\| class="wikitable"
		+	\|-
		+	Advanced Parameters
		+	* [[Parameter: M3UA: Only one hardware unit is active\|Only one hardware unit is active]]
		+	* [[Parameter: M3UA: Destination Restrict supported\|Destination Restrict supported]]
		+	* [[Parameter: M3UA: Congestion level 1\|Congestion level 1]]
		+	* [[Parameter: M3UA: Congestion level 2\|Congestion level 2]]
		+	* [[Parameter: M3UA: Congestion level 3\|Congestion level 3]]
		+	* [[Parameter: M3UA: Restart Timer\|Restart Timer]]
		+	* [[Parameter: M3UA: MTP3 Status Timer\|MTP3 Status Timer]]
		+	* [[Parameter: M3UA: AS Pending Timer\|AS Pending Timer]]
		+	* [[Parameter: M3UA: Heartbeat Timer\|Heartbeat Timer]]
		+	* [[Parameter: M3UA: ASP Up Timer\|ASP Up Timer]]
		+	* [[Parameter: M3UA: ASP Down Timer\|ASP Down Timer]]
		+	* [[Parameter: M3UA: ASP Messages Timeout\|ASP Messages Timeout]]
		+	* [[Parameter: M3UA: DAUD Timer\|DAUD Timer]]
		+	* [[Parameter: M3UA: DRKM Timer\|DRKM Timer]]
		+	* [[Parameter: M3UA: Number of DKRM messages\|Number of DKRM messages]]
		+	* [[Parameter: M3UA: DUNA Settle Timeout\|DUNA Settle Timeout]]
		+	* [[Parameter: M3UA: Sequence Control Timer\|Sequence Control Timer]]
		+
		+	\|}
		+	</div>

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.7.''''' ===
+=== '''''Applies to version(s): v2.8.''''' ===
 {{DISPLAYTITLE:Creating an M3UA Configuration (SGP)}}
 To set up your M3UA system as a Signaling Gateway Process (SGP), you must first create a new M3UA configuration.

@@ Line 18: / Line 18: @@
 * Click '''Create'''
-[[Image:Create_M3UA_SGP.jpg]]
+[[Image:CreateM3ua_SGP_1.png]]
 - Verify that the '''"M3ua Cfg was successfully created"''' message appears