Toolpack:Creating an M3UA SAP (SGP) B - Revision history

Allyntree: /* List of Parameters */ added sap timers and advance parameters

2015-09-28T17:33:40Z

List of Parameters: added sap timers and advance parameters

Allyntree: /* List of Parameters */

2015-06-26T17:42:24Z

List of Parameters

Allyntree: /* List of Parameters */

2015-06-23T18:31:35Z

List of Parameters

Allyntree at 18:29, 23 June 2015

2015-06-23T18:29:46Z

Allyntree: Created page with "=== '''''Applies to version(s): v2.8''''' === {{DISPLAYTITLE:Creating an M3UA SAP (SGP)}} Once an M3UA configuration is created, you must then create a new M3UA service access..."

2015-06-23T18:27:01Z

Created page with "=== '''''Applies to version(s): v2.8''''' === {{DISPLAYTITLE:Creating an M3UA SAP (SGP)}} Once an M3UA configuration is created, you must then create a new M3UA service access..."

New page

=== '''''Applies to version(s): v2.8''''' ===
{{DISPLAYTITLE:Creating an M3UA SAP (SGP)}}
Once an M3UA configuration is created, you must then create a new M3UA service access point (SAP) for your system. The SAP is an identifying label for endpoints in your network.

To create an M3UA SAP:

1- Click '''M3UA''' in the navigation panel:

[[Image:CreateM3ua_0.png]]

2- Click '''Create New M3ua Sap''' in the M3UA configuration panel

[[Image:Create_M3UA_SAP_0.png]]

3- Configure the new SAP:

* Enter a '''name''' for the SAP
* Select an '''Unit''' to use
* Select an '''SCTP source port'''
* Click '''Create'''

[[Image:Create_M3UA_SAP_1_1.png]]

4- Verify that the '''"M3ua Sap was successfully created"''' message appears

[[Image:Create_M3UA_SAP_2.png]]

5- Associate an IP interface with the new SAP:

* Select an available '''IP interface'''
* Click the'''"<<"''' button to associate the interface with the SAP

[[Image:Create_M3UA_SAP_3.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: SCTP Adapter|SCTP Adapter]]
* [[Parameter: SCTP Source Port|SCTP Source Port]]

← Older revision		Revision as of 17:33, 28 September 2015
Line 42:		Line 42:
	* [[Parameter: SCTP Adapter\|SCTP Adapter]]		* [[Parameter: SCTP Adapter\|SCTP Adapter]]
	* [[Parameter: SCTP Source Port\|SCTP Source Port]]		* [[Parameter: SCTP Source Port\|SCTP Source Port]]
		+
		+
		+	'''M3UA SAP Timers'''
		+	* [[Parameter: SCTP Primitive Timer\|SCTP Primitive Timer]]
		+	* [[Parameter: SCTP Association Timer\|SCTP Association Timer]]
		+
		+
		+	<div class="mw-collapsible mw-collapsed" data-collapsetext="SCTP SAP Advanced Parameters" data-expandtext="SCTP SAP Advanced Parameters" style="width: 400px;">
		+	{\| class="wikitable"
		+	\|-
		+
		+	* [[Parameter: Maximum data size\|Maximum data size]]
		+	* [[Parameter: Maximum ACK delay\|Maximum ACK delay]]
		+	* [[Parameter: Maximum datagram before ACK\|Maximum datagram before ACK]]
		+	* [[Parameter: Initial Retransmission Timeout (RTO)\|Initial Retransmission Timeout (RTO)]]
		+	* [[Parameter: Minimum Retransmission Timeout (RTO)\|Minimum Retransmission Timeout (RTO)]]
		+	* [[Parameter: Maximum Retransmission Timeout (RTO)\|Maximum Retransmission Timeout (RTO)]]
		+	* [[Parameter: Freeze timer\|Freeze timer]]
		+	* [[Parameter: Bundle timer\|Bundle timer]]
		+	* [[Parameter: Cookie life time\|Cookie life time]]
		+	* [[Parameter: Delay between heartbeat\|Delay between heartbeat]]
		+	* [[Parameter: Maximum datagram burst\|Maximum datagram burst]]
		+	* [[Parameter: Maximum heartbeat at each RTO\|Maximum heartbeat at each RTO]]
		+	* [[Parameter: Shutdown Guard Timer\|Shutdown Guard Timer]]
		+	* [[Parameter: Handle INIT datagram\|Handle INIT datagram]]
		+	* [[Parameter: Abort negociation if nb. streams mismatch\|Abort negociation if nb. streams mismatch]]
		+	* [[Parameter: Flow-control up threshold\|Flow-control up threshold]]
		+	* [[Parameter: Flow-control down threshold\|Flow-control down threshold]]
		+
		+	\|}
		+	</div>

@@ Line 40: / Line 40: @@
 * [[Parameter: Name|Name]]
-* [[Parameter: SCTP Adapter|Unit to Use]]
+* [[Parameter: SCTP Adapter|SCTP Adapter]]
 * [[Parameter: SCTP Source Port|SCTP Source Port]]

@@ Line 12: / Line 12: @@
 - Click '''Create New M3ua Sap''' in the M3UA configuration panel
-[[Image:Create_M3UA_SAP_0.png]]
+[[Image:Create_M3UA_SAP_0_0.png]]
@@ Line 22: / Line 22: @@
 * Click '''Create'''
-[[Image:Create_M3UA_SAP_1_1.png]]
+[[Image:Create_M3UA_SAP_1.png]]