Toolpack:Creating an MTP3 Configuration A - Revision history

Allyntree at 18:41, 17 December 2012

2012-12-17T18:41:59Z

2012-07-09T18:33:14Z

2012-06-06T18:44:26Z

2012-06-06T18:43:47Z

2010-08-04T15:31:13Z

2010-07-14T19:44:07Z

2010-06-30T19:59:10Z

2010-06-30T19:58:13Z

2010-06-30T19:57:20Z

2010-06-30T19:54:06Z

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.5, v2.6.''''' ===
+=== '''''Applies to version(s): v2.5''''' ===
 {{DISPLAYTITLE:Creating an MTP3 Configuration}}
 Now that you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.5, v2.6.''''' ===
-{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
+{{DISPLAYTITLE:Creating an MTP3 Configuration}}
 Now that you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.
 [[MTP3_Layer|MTP3]] provides message routing between signaling points in an SS7 network.

← Older revision		Revision as of 18:43, 6 June 2012
Line 1:		Line 1:
		+	=== '''''Applies to version(s): v2.5, v2.6.''''' ===
		+	{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
	Now that you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.		Now that you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.
	[[MTP3_Layer\|MTP3]] provides message routing between signaling points in an SS7 network.		[[MTP3_Layer\|MTP3]] provides message routing between signaling points in an SS7 network.

← Older revision		Revision as of 15:31, 4 August 2010
Line 21:		Line 21:

	[[Image:Toolpack_v2.5_MTP3_Created.png]]		[[Image:Toolpack_v2.5_MTP3_Created.png]]
		+
		+
		+	==List of Parameters==
		+
		+	* [[Parameter: Name\|Name]]
		+	* [[Parameter: Enabled\|Enabled]]
		+	* [[Parameter: SSf Validation\|SSf Validation]]
		+	* [[Parameter: Signaling Point Type\|Signaling Point Type]]
		+	* [[Parameter: Restart Procedure\|Restart Procedure]]

@@ Line 1: / Line 1: @@
-Now that you have created originating and destination point codes (OPC and DPC), you must create an MTP3 configuration for your system.
+Now that you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.
 [[MTP3_Layer|MTP3]] provides message routing between signaling points in an SS7 network.
@@ Line 18: / Line 18: @@
 [[Image:Toolpack_v2.5_Creating_MTP3.png]]
-- Verify that the '''Mtp3Cfg was successfully created''' message appears
+- Verify that the '''"Mtp3Cfg was successfully created"''' message appears
 [[Image:Toolpack_v2.5_MTP3_Created.png]]

@@ Line 14: / Line 14: @@
 * Select '''SP''' as the '''signaling point type'''
 * Select a '''restart procedure'''
 * Click '''Create'''

@@ Line 11: / Line 11: @@
 * Enter a '''name''' for the MTP3 configuration
-* Set '''Enabled''' status
+* Make sure the '''Enabled''' and '''SSf Validation''' boxes are checked
 * Select '''SP''' as the '''signaling point type'''
 * Select a '''restart procedure'''
 * Set a value for '''Transfer Restricted Required'''

← Older revision		Revision as of 19:54, 30 June 2010
Line 1:		Line 1:
		+	Now that you have created originating and destination point codes (OPC and DPC), you must create an MTP3 configuration for your system.
	[[MTP3_Layer\|MTP3]] provides message routing between signaling points in an SS7 network.		[[MTP3_Layer\|MTP3]] provides message routing between signaling points in an SS7 network.