Toolpack:Creating an MTP3 Configuration B - Revision history

Allyntree: /* List of Parameters */

2012-12-17T18:55:07Z

List of Parameters

Allyntree: /* List of Parameters */

2012-12-17T18:51:49Z

List of Parameters

Allyntree: /* Applies to version(s): v2.6 */

2012-12-17T18:48:26Z

Applies to version(s): v2.6

Allyntree: Created page with "=== '''''Applies to version(s): v2.6''''' === {{DISPLAYTITLE:Creating an MTP3 Configuration}} Now that you have set up the MTP2 layer of your SS7 system, you must create an MT..."

2012-12-17T18:46:08Z

Created page with "=== '''''Applies to version(s): v2.6''''' === {{DISPLAYTITLE:Creating an MTP3 Configuration}} Now that you have set up the MTP2 layer of your SS7 system, you must create an MT..."

New page

=== '''''Applies to version(s): v2.6''''' ===
{{DISPLAYTITLE:Creating an MTP3 Configuration}}
Now that you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.
[[MTP3_Layer|MTP3]] provides message routing between signaling points in an SS7 network.

To create an MTP3 configuration:

1- Select '''MTP3''' from the navigation panel

[[Image:Toolpack_v2.5_Navigation_Panel_MTP3.png]]

2- Configure the new MTP3 service:

* Enter a '''name''' for the MTP3 configuration
* Make sure the '''Enabled''' and '''SSf Validation''' boxes are checked
* Select '''SP''' as the '''signaling point type'''
* Select a '''restart procedure'''
* Click '''Create'''

[[Image:Toolpack_v2.5_Creating_MTP3.png]]

3- Verify that the '''"Mtp3Cfg was successfully created"''' message appears

[[Image:Toolpack_v2.5_MTP3_Created.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Enabled|Enabled]]
* [[Parameter: SSf Validation|SSf Validation]]
* [[Parameter: Signaling Point Type|Signaling Point Type]]
* [[Parameter: Restart Procedure|Restart Procedure]]

@@ Line 29: / Line 29: @@
 * [[Parameter: Enabled|Enabled]]
 * [[Parameter: SSf Validation|SSf Validation]]
-* [[Parameter: MTP3Signaling Point Type|Signaling Point Type]]
+* [[Parameter: Signaling Point Type|Signaling Point Type]]
-* [[Parameter: Restart Procedure|Restart Procedure]]
+* [[Parameter: MTP3 T15 Timer|T15 Timer]]
-* [[Parameter: Restart Procedure|Restart Procedure]]
+* [[Parameter: MTP3 T16 Timer|T16 Timer]]
-* [[Parameter: Restart Procedure|Restart Procedure]]
+* [[Parameter: MTP3 T18 Timer|T18 Timer]]
-* [[Parameter: Restart Procedure|Restart Procedure]]
+* [[Parameter: MTP3 T19 Timer|T19 Timer]]
-* [[Parameter: Restart Procedure|Restart Procedure]]
+* [[Parameter: MTP3 T21 Timer|T21 Timer]]
-* [[Parameter: Restart Procedure|Restart Procedure]]
+* [[Parameter: MTP3 T26 Timer|T26 Timer]]
-* [[Parameter: Restart Procedure|Restart Procedure]]
-−
 * [[Parameter: Restart Procedure|Restart Procedure]]

@@ Line 18: / Line 18: @@
 * Click '''Create'''
-[[Image:Toolpack_v2.5_Creating_MTP3.png]]
+[[Image:Toolpack_v2.6_Creating_MTP3.png]]
 - Verify that the '''"Mtp3Cfg was successfully created"''' message appears
 [[Image:Toolpack_v2.5_MTP3_Created.png]]
 ==List of Parameters==