Toolpack:Creating an MTP3 Configuration E - Revision history

Allyntree at 18:37, 25 November 2020

2020-11-25T18:37:51Z

Allyntree at 13:39, 21 August 2020

2020-08-21T13:39:13Z

Allyntree at 15:40, 29 November 2017

2017-11-29T15:40:25Z

Allyntree at 16:50, 22 November 2017

2017-11-22T16:50:43Z

Allyntree at 15:34, 3 February 2017

2017-02-03T15:34:37Z

Allyntree: Added northbound interface data

2016-01-04T22:32:50Z

Added northbound interface data

Allyntree: Created page with "=== '''''Applies to version(s): v2.9''''' === {{DISPLAYTITLE:Creating an MTP3 Configuration}} Once you have set up the MTP2 layer of your SS7 system, you must create an MTP3 c..."

2015-11-30T19:44:36Z

Created page with "=== '''''Applies to version(s): v2.9''''' === {{DISPLAYTITLE:Creating an MTP3 Configuration}} Once you have set up the MTP2 layer of your SS7 system, you must create an MTP3 c..."

New page

=== '''''Applies to version(s): v2.9''''' ===
{{DISPLAYTITLE:Creating an MTP3 Configuration}}
Once you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.
[[MTP3_Layer|MTP3]] provides message routing between signaling points in an SS7 network.

To create an MTP3 configuration:

1- Select '''MTP3''' from the navigation panel

[[Image:Mtp3_0_A.png]]

2- Configure the new MTP3 service:

* Enter a '''name''' for the MTP3 configuration
* Make sure the '''Enabled''' and '''SSf Validation''' boxes are checked
* Select '''SP''' as the '''signaling point type'''
* Click '''Create'''

[[Image:Mtp3_1_A.png]]

3- Verify that the '''"Mtp3Cfg was successfully created"''' message appears

[[Image:Mtp3_2_A.png]]

<div class="mw-collapsible mw-collapsed" data-collapsetext="Northbound Interface" data-expandtext="Northbound Interface" style="width: 400px;">

'''Path'''
<pre>
</pre>

'''Parameters (text)'''
<pre>
</pre>

'''Parameters (json)'''
<pre>
</pre>
</div>

==List of Parameters==
* [[Parameter: Name|Name]]
* [[Parameter: Enabled|Enabled]]
* [[Parameter: Signaling Point Type|Signaling Point Type]]

'''Timers'''
* [[Parameter: MTP3 T15 Timer|T15 Timer]]
* [[Parameter: MTP3 T16 Timer|T16 Timer]]
* [[Parameter: MTP3 T18 Timer|T18 Timer]]
* [[Parameter: MTP3 T19 Timer|T19 Timer]]
* [[Parameter: MTP3 T21 Timer|T21 Timer]]
* [[Parameter: MTP3 T26 Timer|T26 Timer]]

'''Advanced Parameters'''
* [[Parameter: MTP3 Ssf Validation|Ssf Validation]]
* [[Parameter: MTP3 Transfer Restricted required|Transfer Restricted required]]

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.9, v2.10, v3.0''' ===
+=== '''''Applies to version(s): 2.9, 2.10, 3.0, 3.2''' ===
 {{DISPLAYTITLE:Creating an MTP3 Configuration}}
 Once you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.9, v2.10, v3.0'''' ===
+=== '''''Applies to version(s): v2.9, v2.10, v3.0''' ===
 {{DISPLAYTITLE:Creating an MTP3 Configuration}}
 Once you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.9, v2.10''''' ===
+=== '''''Applies to version(s): v2.9, v2.10, v3.0'''' ===
 {{DISPLAYTITLE:Creating an MTP3 Configuration}}
 Once you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.

@@ Line 28: / Line 28: @@
 '''Path'''
 <pre>
 </pre>
 '''Parameters (text)'''
 <pre>
 </pre>
 '''Parameters (json)'''
 <pre>
 </pre>
 </div>