Toolpack:Creating an SCCP LSAP B - Revision history

Allyntree: /* List of Parameters */ Added Max Msg Length parameter

2015-09-30T18:57:56Z

List of Parameters: Added Max Msg Length parameter

Allyntree at 17:22, 26 September 2014

2014-09-26T17:22:42Z

Allyntree at 17:22, 26 September 2014

2014-09-26T17:22:15Z

Allyntree: New 2.8 article

2014-09-26T17:18:14Z

New 2.8 article

Allyntree: New 2.8 article

2014-09-26T17:17:07Z

New 2.8 article

New page

=== '''''Applies to version(s): v2.5, v2.6, 2.7''''' ===
{{DISPLAYTITLE:Creating an SCCP LSAP}}
Now that you have created an [[SCCP]] network, you must create a new SCCP lower service access point ([[LSAP]]).

Creating an [[Toolpack:Create_an_SCCP_LSAP|LSAP]] tells the [[SCCP]] protocol layer about a collection of [[SS7]] nodes that are accessible through [[MTP3 Layer|MTP3]].

To Create an SCCP LSAP:

1- Select '''SCCP''' from the navigation panel

[[Image:Create_SCCP_Stack_0.png]]

2- Select an SCCP Network

[[Image:Select_SCCP_Network_0.png]]

3- Click '''Create New SCCP LSAP''' in the [[SCCP]] network configuration window

[[Image:Toolpack_v2.5_Create_SCCP_LSAP.png]]

4- Configure the new SCCP LSAP:

* Enter a [[Parameter: Name|Name]] for the LSAP
* Click '''Save'''

[[Image:Toolpack_v2.5_Creating_SCCP_LSAP.png]]

5- Verify that the '''"SccpLsap was successfully created"''' message appears

[[Image:Toolpack_v2.5_SCCP_LSAP_Created.png]]

==List of Parameters==

* [[Parameter: Name|Name]]

← Older revision		Revision as of 18:57, 30 September 2015
Line 42:		Line 42:

	* [[Parameter: Name\|Name]]		* [[Parameter: Name\|Name]]
		+
		+	'''Advanced Parameters'''
		+	* [[Parameter: Max Msg Length\|Max Msg Length]]

@@ Line 28: / Line 28: @@
 * Enter a [[Parameter: Name|Name]] for the LSAP
-* Click '''Save'''
+* Click '''Create'''
 [[Image:Create_SCCP_LSAP_1.png]]

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.5, v2.6, 2.7''''' ===
+=== '''''Applies to version(s): v2.8''''' ===
 {{DISPLAYTITLE:Creating an SCCP LSAP}}
-Now that you have created an [[SCCP]] network, you must create a new SCCP lower service access point ([[LSAP]]).
+After you create an [[SCCP]] network, you must create a new SCCP lower service access point ([[LSAP]]).
 Creating an [[Toolpack:Create_an_SCCP_LSAP|LSAP]] tells the [[SCCP]] protocol layer about a collection of [[SS7]] nodes that are accessible through [[MTP3 Layer|MTP3]].

@@ Line 22: / Line 22: @@
-[[Image:Toolpack_v2.5_Create_SCCP_LSAP.png]]
+[[Image:Create_SCCP_LSAP_0.png]]
@@ Line 30: / Line 30: @@
 * Click '''Save'''
-[[Image:Toolpack_v2.5_Creating_SCCP_LSAP.png]]
+[[Image:Create_SCCP_LSAP_1.png]]
 - Verify that the '''"SccpLsap was successfully created"''' message appears
-[[Image:Toolpack_v2.5_SCCP_LSAP_Created.png]]