Toolpack:Creating an SCCP Route A - Revision history

Allyntree: typo

2014-09-26T17:37:02Z

typo

2013-07-15T15:30:36Z

2012-07-09T18:39:27Z

2012-06-06T19:02:40Z

2012-06-06T19:02:17Z

2012-05-11T16:55:05Z

2012-05-11T16:31:03Z

2012-05-11T15:39:22Z

2012-05-11T14:13:39Z

2012-05-11T14:00:49Z

← Older revision		Revision as of 17:37, 26 September 2014
Line 31:		Line 31:
	[[Image:SCCP_Route_Backup_PC.png]]		[[Image:SCCP_Route_Backup_PC.png]]

−	* '''Note: For each selected point codes, a valid SCCP route must be exist'''.	+	* '''Note: For each selected point codes, a valid SCCP route must exist'''.

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.5, v2.6.''''' ===
+=== '''''Applies to version(s): v2.5, v2.6, v2.7''''' ===
 {{DISPLAYTITLE:Creating an SCCP Route}}
 Now that you have created an [[SCCP]] [[LSAP]], you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system.

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.5, v2.6.''''' ===
-{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
+{{DISPLAYTITLE:Creating an SCCP Route}}
 Now that you have created an [[SCCP]] [[LSAP]], you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system.
 This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).

← Older revision		Revision as of 19:02, 6 June 2012
Line 1:		Line 1:
		+	=== '''''Applies to version(s): v2.5, v2.6.''''' ===
		+	{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
	Now that you have created an [[SCCP]] [[LSAP]], you must create a new [[Toolpack:Create_an_SCCP_Route\|SCCP route]] for your system.		Now that you have created an [[SCCP]] [[LSAP]], you must create a new [[Toolpack:Create_an_SCCP_Route\|SCCP route]] for your system.
	This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).		This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).

← Older revision		Revision as of 16:55, 11 May 2012
Line 30:		Line 30:

	* '''Note: For each selected point codes, a valid SCCP route must be exist'''.		* '''Note: For each selected point codes, a valid SCCP route must be exist'''.
		+
		+
		+	5- '''Next Step:''' [[Toolpack_v2.5:Creating_an_SCCP_SSN\|Create an SCCP SSN]]

	==List of Parameters==		==List of Parameters==

← Older revision		Revision as of 16:31, 11 May 2012
Line 38:		Line 38:
	* [[Parameter: SLS Mask\|SLS Mask]] (For ANSI and TELCORDIA variants only)		* [[Parameter: SLS Mask\|SLS Mask]] (For ANSI and TELCORDIA variants only)
	* [[Parameter: Destination Point Code\|Destination Point Code]]		* [[Parameter: Destination Point Code\|Destination Point Code]]
		+
		+	==Navigation==
		+	{\| class="wikitable"
		+	\|-
		+	! Previous !! Next
		+	\|-
		+	\| [[Toolpack_v2.5:Creating_an_SCCP_LSAP\|Create an SCCP LSAP]] \|\| [[Toolpack_v2.5:Creating_an_SCCP_SSN\|Create an SCCP SSN]]
		+	\|}

@@ Line 1: / Line 1: @@
-Now that you have created an [[SCCP]] LSAP, you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system.
+Now that you have created an [[SCCP]] [[LSAP]], you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system.
 This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).
@@ Line 26: / Line 26: @@
 - Configure [[SCCP Route Backup Point Code]]
-* Assign [[Parameter: SCCP Backup Point Code| Backup Point Codes]] to use in case this route's DPC is not available.
+* Assign [[Parameter: SCCP Backup Point Code| Backup Point Codes]] to use in case this route's [[DPC]] is not available.
 [[Image:SCCP_Route_Backup_PC.png]]

@@ Line 15: / Line 15: @@
 * Select a [[Parameter: Replication Mode|Replication Mode]] (ANSI96 and TELCORDIA variants)
 * Select an [[Parameter: SLS Mask|SLS Mask]] (ANSI and TELCORDIA protocol variants)
-* Select a [[Parameter: Destination Point Code|Destination Point Code]] (DPC) of the node where the route is terminating
+* Select a [[Parameter: Destination Point Code|Destination Point Code]] for this route
 * Click '''Create'''
@@ Line 24: / Line 24: @@
 [[Image:Toolpack_v2.5_SCCP_Route_Created.png]]
 ==List of Parameters==