Toolpack:Creating an SCCP Route B - Revision history

Allyntree: /* List of Parameters */ Added Broadband Support parameter

2015-09-30T19:02:12Z

List of Parameters: Added Broadband Support parameter

Allyntree: /* Applies to version(s): v2.8 */

2014-09-26T17:36:41Z

Applies to version(s): v2.8

Allyntree: New 2.8 article

2014-09-26T17:33:22Z

New 2.8 article

Allyntree: New 2.8 artilce

2014-09-26T17:25:42Z

New 2.8 artilce

New page

=== '''''Applies to version(s): v2.8''''' ===
{{DISPLAYTITLE:Creating an SCCP Route}}
Now that you have created an [[SCCP]] [[LSAP]], you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system.
This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).

To Create an SCCP Route:

- Select '''SCCP''' from the navigation panel

[[Image:Create_SCCP_Stack_0.png]]

2- Select an SCCP Network

[[Image:Select_SCCP_Network_0.png]]

3- Click '''Create new Sccp Route''' in the SCCP LSAP configuration window

[[Image:Toolpack_v2.5_Create_SCCP_Route.png]]

4- Configure the new SCCP Route:

* Choose a [[Parameter: Name|Name]] for the new route
* Select a [[Parameter: Protocol Type|Protocol Variant]]
* Select a [[Parameter: Replication Mode|Replication Mode]] (ANSI96 and TELCORDIA variants)
* Select an [[Parameter: SLS Mask|SLS Mask]] (ANSI and TELCORDIA protocol variants)
* Select a [[Parameter: Destination Point Code|Destination Point Code]] for this route
* Click '''Create'''

[[Image:Toolpack_v2.5_Creating_SCCP_Route.png]]

5- Verify that the '''"SccpRoute was successfully created"''' message appears

[[Image:Toolpack_v2.5_SCCP_Route_Created.png]]

6- Configure [[SCCP Route Backup Point Code]]

* Assign [[Parameter: SCCP Backup Point Code| Backup Point Codes]] to use in case this route's [[DPC]] is not available.
[[Image:SCCP_Route_Backup_PC.png]]

* '''Note: For each selected point codes, a valid SCCP route must be exist'''.

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Protocol Type|Protocol Variant]]
* [[Parameter: Replication Mode|Replication Mode]]
* [[Parameter: SLS Mask|SLS Mask]] (For ANSI and TELCORDIA variants only)
* [[Parameter: Destination Point Code|Destination Point Code]]

← Older revision		Revision as of 19:02, 30 September 2015
Line 62:		Line 62:
	* [[Parameter: SLS Mask\|SLS Mask]] (For ANSI and TELCORDIA variants only)		* [[Parameter: SLS Mask\|SLS Mask]] (For ANSI and TELCORDIA variants only)
	* [[Parameter: Destination Point Code\|Destination Point Code]]		* [[Parameter: Destination Point Code\|Destination Point Code]]
		+
		+	'''Advanced Parameters'''
		+	* [[Parameter: Broadband Support\|Broadband Support]]

@@ Line 53: / Line 53: @@
 [[Image:Create_SCCP_Route_3.png]]
-* '''Note: For each selected point codes, a valid SCCP route must be exist'''.
+* '''Note: For each selected point codes, a valid SCCP route must exist'''.
-−
 ==List of Parameters==

@@ Line 7: / Line 7: @@
 - Select '''SCCP''' from the navigation panel
@@ Line 19: / Line 19: @@
-- Click '''Create new Sccp Route''' in the SCCP LSAP configuration window
+- Select an SCCP LSAP
 - Configure the new SCCP Route:
 * Choose a [[Parameter: Name|Name]] for the new route
@@ Line 33: / Line 39: @@
 * Click '''Create'''
-[[Image:Toolpack_v2.5_Creating_SCCP_Route.png]]
+[[Image:Create_SCCP_Route_1.png]]
 - Verify that the '''"SccpRoute was successfully created"''' message appears
-[[Image:Toolpack_v2.5_SCCP_Route_Created.png]]
+[[Image:Create_SCCP_Route_2.png]]
 - Configure [[SCCP Route Backup Point Code]]
 * Assign [[Parameter: SCCP Backup Point Code| Backup Point Codes]] to use in case this route's [[DPC]] is not available.
-[[Image:SCCP_Route_Backup_PC.png]]
 * '''Note: For each selected point codes, a valid SCCP route must be exist'''.