Toolpack:Creating an SCCP Userpart B - Revision history

Allyntree: /* Applies to version(s): v2.8 */

2015-12-02T18:51:51Z

Applies to version(s): v2.8

Luc Morissette: immiediate

2015-05-14T13:46:52Z

immiediate

Allyntree at 17:15, 26 September 2014

2014-09-26T17:15:47Z

Allyntree at 17:15, 26 September 2014

2014-09-26T17:15:25Z

Allyntree at 17:05, 26 September 2014

2014-09-26T17:05:41Z

Allyntree: New 2.8 articel

2014-09-26T16:57:00Z

New 2.8 articel

New page

=== '''''Applies to version(s): v2.5, v2.6, v2.7''''' ===
{{DISPLAYTITLE:Creating an SCCP Userpart}}
Now that you have configured an [[SCCP]] network:

* If you are using [[SCCP]] to perform [[Global Title|Global Title (GT)]] routing/translation ([[GTT]]) in '''standalone mode''', then skip this step. Go to [[Toolpack_v2.5:Creating_an_SCCP_LSAP|Create an SCCP LSAP]].

* If you are using a [[TCAP]], you must create a new [[SCCP]] user part, so that you can bind the SCCP and TCAP later on.
<BR>
----

The user part is the container for the multiple [[SCCP]] interfaces. One user part is required for each protocol variant.
Multiple [[SCCP]] user parts can be instantiated within a single [[SCCP]] protocol layer. This allows a user application to interface with multiple [[SS7]] [[SCCP]] protocol variants at the same time. Only one [[SCCP]] user part is required for a specific variant as it can be assigned to multiple SCCP networks.

A user part can easily be seen as a protocol variant that a host application wants to use on the SS7 network.

To create an SCCP user part:

1- Select '''SCCP''' from the navigation panel

[[Image:Create_SCCP_Stack_0.png]]

1- Select an SCCP Network

[[Image:Select_SCCP_Network_0.png]]

1- Click '''Create New SCCP User Part''' to access the SCCP configuration window

[[Image:Create_SCCP_Userpart_0.png]]

2- Configure the new [[SCCP]] user part

* Enter a [[Parameter: Name|Name]] for the user part
* Enter a [[Parameter: Sub-System Number|Sub-System Number]] to assign to this UserPart (upper [[TCAP]] application)
* Select the [[Parameter: SCCP Concerned Point Code|First Concerned Point Code]] that needs immiediate notification of own [[SSN]] status changes
* Select the [[Parameter: SCCP Concerned Point Code|Second Concerned Point Code]] that needs immiediate notification of own [[SSN]] status changes
* Click '''Create'''

[[Image:Create_SCCP_Userpart_1.png]]

3- Verify that the '''"SCCP Userpart was successfully created"''' message appears

[[Image:Create_SCCP_Userpart_2.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Sub-System Number|Sub-System Number]]
* [[Parameter: SCCP Concerned Point Code|First Concerned Point Code]]
* [[Parameter: SCCP Concerned Point Code|Second Concerned Point Code]]

← Older revision		Revision as of 17:15, 26 September 2014
Line 20:		Line 20:

	[[Image:Create_SCCP_Stack_0.png]]		[[Image:Create_SCCP_Stack_0.png]]
		+

	2- Select an SCCP Network		2- Select an SCCP Network

@@ Line 3: / Line 3: @@
 Now that you have configured an [[SCCP]] network:
-* If you are using [[SCCP]] to perform [[Global Title|Global Title (GT)]] routing/translation ([[GTT]]) in '''standalone mode''', then skip this step. Go to [[Toolpack_v2.5:Creating_an_SCCP_LSAP|Create an SCCP LSAP]].
+* If you are using [[SCCP]] to perform [[Global Title|Global Title (GT)]] routing/translation ([[GTT]]) in '''standalone mode''', then skip this step. Go to [[Toolpack:Creating_an_SCCP_LSAP_B|Create an SCCP LSAP]].
 * If you are using a [[TCAP]], you must create a new [[SCCP]] user part, so that you can bind the SCCP and TCAP later on.

@@ Line 38: / Line 38: @@
 * Enter a [[Parameter: Name|Name]] for the user part
 * Enter a [[Parameter: Sub-System Number|Sub-System Number]] to assign to this UserPart (upper [[TCAP]] application)
-* Select the [[Parameter: SCCP Concerned Point Code|First Concerned Point Code]] that needs immiediate notification of own [[SSN]] status changes
+* Select the [[Parameter: SCCP Concerned Point Code|First Concerned Point Code]] that needs immediate notification of own [[SSN]] status changes
-* Select the [[Parameter: SCCP Concerned Point Code|Second Concerned Point Code]] that needs immiediate notification of own [[SSN]] status changes
+* Select the [[Parameter: SCCP Concerned Point Code|Second Concerned Point Code]] that needs immediate notification of own [[SSN]] status changes
 * Click '''Create'''
@@ Line 49: / Line 49: @@
 [[Image:Create_SCCP_Userpart_2.png]]
 ==List of Parameters==

@@ Line 21: / Line 21: @@
 [[Image:Create_SCCP_Stack_0.png]]
 - Select an SCCP Network
@@ Line 27: / Line 27: @@
 - Click '''Create New SCCP User Part''' to access the SCCP configuration window
@@ Line 33: / Line 33: @@
 - Configure the new [[SCCP]] user part
 * Enter a [[Parameter: Name|Name]] for the user part
@@ Line 45: / Line 45: @@
 - Verify that the '''"SCCP Userpart was successfully created"''' message appears
 [[Image:Create_SCCP_Userpart_2.png]]

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v2.5, v2.6, v2.7''''' ===
+=== '''''Applies to version(s): v2.8''''' ===
 {{DISPLAYTITLE:Creating an SCCP Userpart}}
 Now that you have configured an [[SCCP]] network: