Toolpack:Creating the M2PA Configuration B - Revision history

Allyntree at 16:57, 18 September 2014

2014-09-18T16:57:08Z

Allyntree: /* List of Parameter */

2014-09-18T14:46:14Z

List of Parameter

Allyntree: /* Applies to version(s): v2.7. */

2014-09-18T14:45:57Z

Applies to version(s): v2.7.

Allyntree: /* Applies to version(s): v2.7. */

2014-09-18T14:45:37Z

Applies to version(s): v2.7.

Allyntree: /* Applies to version(s): v2.7. */

2014-09-18T14:45:23Z

Applies to version(s): v2.7.

Allyntree: This was a copy and paste of SCTP and a good part of it remained as SCTP. Note: the second and third images are taken from a 2.8 system.

2014-09-18T14:44:58Z

This was a copy and paste of SCTP and a good part of it remained as SCTP. Note: the second and third images are taken from a 2.8 system.

Allyntree: Created page with "=== '''''Applies to version(s): v2.7.''''' === {{DISPLAYTITLE:Creating the SCTP Configuration}} Stream Control Transmission Protocol (SCTP), a Transport Layer protocol, ensure..."

2013-07-15T14:51:02Z

Created page with "=== '''''Applies to version(s): v2.7.''''' === {{DISPLAYTITLE:Creating the SCTP Configuration}} Stream Control Transmission Protocol (SCTP), a Transport Layer protocol, ensure..."

New page

=== '''''Applies to version(s): v2.7.''''' ===
{{DISPLAYTITLE:Creating the SCTP Configuration}}
Stream Control Transmission Protocol (SCTP), a Transport Layer protocol, ensures reliable, in-sequence transport of messages.

To edit your system's SCTP configuration:

1- Select '''SCTP''' from the navigation panel

[[Image:M2pa_0.png]]

2- Configure the SCTP service

* Make sure the box labelled '''Enabled''' is '''checked'''
* Enter a '''name''' for the SCTP service
* Select an appropriate '''service type''':
** [[RAW IP|RAW_IP]]
** [[UDP IP|UDP]]
* Click '''Create'''

[[Image:Toolpack_v2.5_Creating_SCTP.png]]

3- Verify that the '''"Sctp Cfg was successfully created"''' message appears

[[Image:Toolpack_v2.5_SCTP_Created.png]]

==List of Parameter==

* [[Parameter: Name|Name]]
* [[Parameter: Service Type|Service Type]]

@@ Line 15: / Line 15: @@
 * Click '''Create'''
-[[Image:CreateM2pa_1.png]]
+[[Image:CreateM2pa_1_a.png]]
 - Verify that the '''"M2ua Cfg was successfully created"''' message appears

← Older revision		Revision as of 14:46, 18 September 2014
Line 24:		Line 24:

	* [[Parameter: Name\|Name]]		* [[Parameter: Name\|Name]]
−	* [[Parameter: Service Type\|Service Type]]

@@ Line 17: / Line 17: @@
 [[Image:CreateM2pa_1.png]]
-- Verify that the '''"Sctp Cfg was successfully created"''' message appears
+- Verify that the '''"M2ua Cfg was successfully created"''' message appears
 [[Image:CreateM2pa_2.png]]

@@ Line 3: / Line 3: @@
-To edit your system's M2PA configuration:
+To create an M2PA configuration:
 - Select '''M2PA''' from the navigation panel
@@ Line 20: / Line 20: @@
 [[Image:CreateM2pa_2.png]]
 ==List of Parameter==

@@ Line 9: / Line 9: @@
 [[Image:M2pa_0.png]]
-- Configure the SCTP service
+- Configure the M2PA service
 * Make sure the box labelled '''Enabled''' is '''checked'''

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.7.''''' ===
-{{DISPLAYTITLE:Creating the SCTP Configuration}}
+{{DISPLAYTITLE:Creating the M2PA Configuration}}
-Stream Control Transmission Protocol (SCTP), a Transport Layer protocol, ensures reliable, in-sequence transport of messages.
-To edit your system's SCTP configuration:
+To edit your system's M2PA configuration:
-- Select '''SCTP''' from the navigation panel
+- Select '''M2PA''' from the navigation panel
 [[Image:M2pa_0.png]]
@@ Line 12: / Line 12: @@
 * Make sure the box labelled '''Enabled''' is '''checked'''
-* Enter a '''name''' for the SCTP service
+* Enter a '''name''' for the M2PA service
-* Select an appropriate '''service type''':
-** [[RAW IP|RAW_IP]]
-** [[UDP IP|UDP]]
 * Click '''Create'''
-[[Image:Toolpack_v2.5_Creating_SCTP.png]]
+[[Image:CreateM2pa_1.png]]
 - Verify that the '''"Sctp Cfg was successfully created"''' message appears
-[[Image:Toolpack_v2.5_SCTP_Created.png]]
+[[Image:CreateM2pa_2.png]]