Toolpack:Creating the M2UA Configuration A - Revision history

Allyntree at 18:45, 9 July 2012

2012-07-09T18:45:39Z

Allyntree: moved Toolpack v2.5:Creating the M2UA Configuration to Toolpack:Creating the M2UA Configuration A: New naming convention

2012-06-07T22:17:08Z

moved Toolpack v2.5:Creating the M2UA Configuration to Toolpack:Creating the M2UA Configuration A: New naming convention

Allyntree at 22:16, 7 June 2012

2012-06-07T22:16:40Z

Allyntree: /* Lit of Parameters */

2011-07-18T00:39:20Z

Lit of Parameters

Allyntree at 22:56, 17 July 2011

2011-07-17T22:56:18Z

Allyntree at 21:24, 6 August 2010

2010-08-06T21:24:43Z

Allyntree at 16:46, 15 July 2010

2010-07-15T16:46:03Z

Allyntree: Created page with 'To create an M2UA configuration: 1- Click '''M2UA''' in the navigation panel Image:Toolpack_v2.5_Navigation_Panel_M2UA.png 2- Create the M2UA configuration: * Enter a '''…'

2010-07-05T18:24:04Z

Created page with 'To create an M2UA configuration: 1- Click '''M2UA''' in the navigation panel Image:Toolpack_v2.5_Navigation_Panel_M2UA.png 2- Create the M2UA configuration: * Enter a '''…'

New page

To create an M2UA configuration:

1- Click '''M2UA''' in the navigation panel

[[Image:Toolpack_v2.5_Navigation_Panel_M2UA.png]]

2- Create the M2UA configuration:

* Enter a '''name''' for the M2UA service
* Click '''Create'''

[[Image:Toolpack_v2.5_Creating_M2UA.png]]

3- Verify that the '''M2ua Cfg was successfully created''' message appears

[[Image:Toolpack_v2.5_M2UA_Created.png]]

@@ Line 1: / Line 1: @@
 === '''''Applies to version(s): v2.5, v2.6.''''' ===
-{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
+{{DISPLAYTITLE:Creating the M2UA Configuration}}
 To create your [[M2UA]] system, you must create a new M2UA configuration.

← Older revision		Revision as of 22:16, 7 June 2012
Line 1:		Line 1:
		+	=== '''''Applies to version(s): v2.5, v2.6.''''' ===
		+	{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
	To create your [[M2UA]] system, you must create a new M2UA configuration.		To create your [[M2UA]] system, you must create a new M2UA configuration.

← Older revision		Revision as of 00:39, 18 July 2011
Line 22:		Line 22:


−	==~~Lit~~ of Parameters==	+	==List of Parameters==

	* [[Parameter: Name\|Name]]		* [[Parameter: Name\|Name]]

@@ Line 1: / Line 1: @@
 To create your [[M2UA]] system, you must create a new M2UA configuration.
-The M2UA (Message Transfer Part 2 User Adaptation Layer) is used to interface the [[MTP2 Layer]] of a signaling gateway to the [[MTP3 Layer]] of a media gateway controller (MGC). M2UA can also be seen as a way to extend an MTP2 link. An M2UA link is always bound to an MTP2 link.
+M2UA (Message Transfer Part 2 User Adaptation Layer) is used to interface the [[MTP2 Layer]] of a signaling gateway to the [[MTP3 Layer]] of a media gateway controller (MGC). M2UA can also be seen as a way to extend an MTP2 link. An M2UA link is always bound to an MTP2 link.
 To create an M2UA configuration:

← Older revision		Revision as of 21:24, 6 August 2010
Line 20:		Line 20:

	[[Image:Toolpack_v2.5_M2UA_Created.png]]		[[Image:Toolpack_v2.5_M2UA_Created.png]]
		+
		+
		+	==Lit of Parameters==
		+
		+	* [[Parameter: Name\|Name]]

@@ Line 1: / Line 1: @@
 To create an M2UA configuration:
 - Click '''M2UA''' in the navigation panel
@@ Line 12: / Line 17: @@
 [[Image:Toolpack_v2.5_Creating_M2UA.png]]
-- Verify that the '''M2ua Cfg was successfully created''' message appears
+- Verify that the '''"M2ua Cfg was successfully created"''' message appears
 [[Image:Toolpack_v2.5_M2UA_Created.png]]