Toolpack:Host 1Plus1 Secondary A - Revision history

Allyntree at 14:05, 11 November 2020

2020-11-11T14:05:48Z

2020-07-21T15:35:48Z

2017-10-10T18:33:09Z

2016-09-27T13:13:59Z

2015-10-13T17:45:01Z

added version

2015-05-25T18:34:39Z

2015-02-09T15:46:35Z

2015-02-09T15:45:24Z

2015-02-09T15:43:57Z

revised steps 4 and 4a

2015-02-04T21:17:13Z

@@ Line 1: / Line 1: @@
 {{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}
+{| class="wikitable"
 The first time that you connect to a gateway, the web portal setup wizard will be displayed and you will be asked to select how you would like to configure the role of the gateway. Your choices are standalone, primary, or secondary. Once the role configuration settings are applied, the gateway will start up and display the web portal configuration management tool.

← Older revision		Revision as of 15:35, 21 July 2020
Line 1:		Line 1:
−	=== '''''Applies to version(s) v2.8, v2.9, v2.10, v3.0''''' ===	+	=== '''''Applies to version(s) v2.8, v2.9, v2.10, v3.0, v3.2''''' ===
	{{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}		{{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}

← Older revision		Revision as of 18:33, 10 October 2017
Line 1:		Line 1:
−	=== '''''Applies to version(s) v2.8, v2.9, v2.10''''' ===	+	=== '''''Applies to version(s) v2.8, v2.9, v2.10, v3.0''''' ===
	{{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}		{{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}

← Older revision		Revision as of 13:13, 27 September 2016
Line 1:		Line 1:
−	=== '''''Applies to version(s) v2.8, v2.9''''' ===	+	=== '''''Applies to version(s) v2.8, v2.9, v2.10''''' ===
	{{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}		{{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}

← Older revision		Revision as of 17:45, 13 October 2015
Line 1:		Line 1:
−	=== '''''Applies to version v2.8''''' ===	+	=== '''''Applies to version(s) v2.8, v2.9''''' ===
	{{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}		{{DISPLAYTITLE:Setting the Role to a Secondary Unit in a 1+1 System}}

← Older revision		Revision as of 15:46, 9 February 2015
Line 23:		Line 23:


−	4- If you need to change the default subnet address or subnet mask, click '''change internal subnets''' and proceed to step 5a, otherwise click '''Continue''' and go to step 5.	+	4- If you need to change the default subnet address or subnet mask, click '''change internal subnets''' and proceed to step 4a, otherwise click '''Continue''' and go to step 5.

	[[Image:HostRoleSecondary_3_A.png]]		[[Image:HostRoleSecondary_3_A.png]]

← Older revision		Revision as of 15:45, 9 February 2015
Line 33:		Line 33:


−	5- Follow the onscreen instructions and connect the two units together. When you have completed the connections, click '''~~Confirm~~'''.	+	5- Follow the onscreen instructions and connect the two units together. When you have completed the connections, click '''Continue'''.

	[[Image:HostRoleSecondary_5_A.png]]		[[Image:HostRoleSecondary_5_A.png]]

@@ Line 23: / Line 23: @@
-- This step is optional, however if you require you may modify the VLAN IDS to use for the control network.
+- If you need to change the default subnet address or subnet mask, click  '''change internal subnets''' and proceed to step 5a, otherwise  click '''Continue''' and go to step 5.
-* Once you are done, click '''Continue'''.
 [[Image:HostRoleSecondary_3_A.png]]
-a- This step is optional and only occurs if you clicked '''change internal subnets''' in the previous step.
+a- Enter the subnet address and subnet mask for each VLAN ID and click '''Continue'''.
-*Enter the subnet address and subnet mask for each VLAN ID and click '''Continue'''.
 [[Image:HostRoleSecondary_4_A.png]]

@@ Line 29: / Line 29: @@
-a- This step is optional and only occurs if you clicked '''change internal subnets''' in step 5.
+a- This step is optional and only occurs if you clicked '''change internal subnets''' in the previous step.
 *Enter the subnet address and subnet mask for each VLAN ID and click '''Continue'''.
@@ Line 35: / Line 35: @@
 - Follow the onscreen instructions and connect the two units together. When you have completed the connections, click '''Confirm'''.
 [[Image:HostRoleSecondary_5_A.png]]
 - Once you are satisfied with your settings, click '''Confirm'''.
 [[Image:HostRoleSecondary_6_A.png]]