Toolpack:M3UA Use Case B:Configure IP Interface A - Revision history

Allyntree at 20:32, 6 September 2019

2019-09-06T20:32:02Z

Allyntree: /* To configure a VoIP0 or VoIP1 port */

2019-09-06T20:31:15Z

To configure a VoIP0 or VoIP1 port

Allyntree: /* Applies to version(s): v3.0 */

2019-09-06T13:34:42Z

Applies to version(s): v3.0

Allyntree: Created page with "=== '''''Applies to version(s): v3.0''''' === {{DISPLAYTITLE:Configuring VoIP Interfaces}} The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the foll..."

2019-08-22T16:21:14Z

Created page with "=== '''''Applies to version(s): v3.0''''' === {{DISPLAYTITLE:Configuring VoIP Interfaces}} The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the foll..."

New page

=== '''''Applies to version(s): v3.0''''' ===
{{DISPLAYTITLE:Configuring VoIP Interfaces}}

The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:

*IP Address
*Netmask
*Gateway

 

== To configure a VoIP0 or VoIP1 port ==

1. Select '''IP Interfaces''' from the navigation panel:

[[Image:Create Voip Interface_0.png]]

 2. Click the '''IP Interfaces''' tab.
*Click '''Create New IP Interface'''

[[Image:Voip_Interface_1a_1.png]]

 3. Configure the IP port:

*Enter a name for the interface
*Select one or more services to use for the IP interface
*Select a '''Virtual port''' from which IP packets will exit.
*Indicate whether or not to use dynamic IP will be used on this interface. For example DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
*Enter an '''IP address'''
*Enter a '''Netmask'''
*Enter a '''gateway address'''
*Click '''Save'''

'''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. 

[[Image:Create Voip Interface_2_1.png]]

 

4. The changes are displayed in the IP interfaces information panel:

[[Image:Create Voip Interface_3_1.png]]

== List of Parameters ==

*[[Parameter: Interface name|Interface name]]
*[[Parameter: Services to use|Services to use]]
*[[Parameter: Virtual port|Virtual port]]
*[[Parameter: Use DHCP|Use dynamic IP]]
*[[Parameter: IP Address|IP Address]]
*[[Parameter: Netmask|Netmask]]
*[[Parameter: Gateway|Gateway]]

@@ Line 4: / Line 4: @@
 In this use case the IP interface of the VoIP0 and VoIP1 ports are configured by setting the following:
-*IP Address: 192.168.0.55
+*IP Address: 192.168.0.99
 *Netmask: 255.255.255.0
 *Gateway: 192.168.0.1

@@ Line 35: / Line 35: @@
 '''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. <br>
-[[Image:Create Voip Interface_2_1.png]]
+[[Image:Create Voip Interface_2_1_1.png]]
 <br>

@@ Line 2: / Line 2: @@
 {{DISPLAYTITLE:Configuring VoIP Interfaces}}
-The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:
+In this use case the IP interface of the VoIP0 and VoIP1 ports are configured by setting the following:
 <br>