Toolpack:Starting Continuity Check ISUP A - Revision history

Allyntree at 19:16, 1 December 2020

2020-12-01T19:16:05Z

Allyntree at 18:00, 21 August 2020

2020-08-21T18:00:09Z

Allyntree at 17:59, 21 August 2020

2020-08-21T17:59:40Z

Nicole Tan: Removed v2.6 from "/* Applies to version(s): v2.6, v2.7. */ "

2013-07-09T19:43:10Z

Removed v2.6 from "- Applies to version(s): v2.6, v2.7.: "

Manon Bélanger: first version of the page for manual continuity check (CCR)

2012-12-14T15:17:05Z

first version of the page for manual continuity check (CCR)

New page

=== '''''Applies to version(s): v2.6, v2.7.''''' ===
{{DISPLAYTITLE:Starting Manual Continuity Check}}

Note: the option might not be available if the resources required for the test (tone generation and detection) are not available.

1- Select '''SS7->ISUP''' from the navigation panel

2- Click on the '''Status''' tab and click on the appropriate ISUP Stack

3- Click on the '''Interfaces''' tab and select the appropriate ISUP Interface

4- Click on the '''Circuit Groups''' tab and select the appropriate Circuit Group

'''If you want to start a continuity check on all circuits of a circuit group:'''
*Select '''Yes''' for'''Start continuity check''' and click on '''Apply states'''
*Click on '''Now''' to refresh the status and see the result of the test. Some of the following stats should be modified:
**Total ccr success cnt
**Total ccr fail cnt
**Last ccr unknown cnt
**Last ccr in progress cnt
**Last ccr success cnt
**Last ccr fail cnt
**Last ccr error cnt

'''If you want to start a continuity check on a specific circuit:'''
*Click on the '''Circuits''' tab and select the circuit in the '''Cic''' column.
*Select '''Yes''' for'''Start continuity check''' and click on '''Apply states'''
*Click on '''Now''' to refresh the status and see the result of the test. Some of the following stats should be modified:
**Nb outgoing ccr success
**Nb outgoing ccr fail
**Last ccr result

← Older revision		Revision as of 19:16, 1 December 2020
Line 1:		Line 1:
−	~~=== '''''Applies to version(s): 2.7, 2.8, 2.9, 3.0, 3.2''''' ===~~
	{{DISPLAYTITLE:Starting Manual Continuity Check}}		{{DISPLAYTITLE:Starting Manual Continuity Check}}
		+	{\| class="wikitable"
		+	\|-
		+	\|rowspan="3"\|This article applies to:
		+	\|'''Product'''
		+	\|'''Version'''
		+	\|-
		+	\|Tmedia
		+	\|2.7, 2.8, 2.9, 2.10, 3.0, 3.2
		+	\|}

	Note: the option might not be available if the resources required for the test (tone generation and detection) are not available.		Note: the option might not be available if the resources required for the test (tone generation and detection) are not available.

← Older revision		Revision as of 17:59, 21 August 2020
Line 1:		Line 1:
−	=== '''''Applies to version(s): v2.7.''''' ===	+	=== '''''Applies to version(s): 2.7, 2.8, 2.9, 3.0, 3.2''''' ===
	{{DISPLAYTITLE:Starting Manual Continuity Check}}		{{DISPLAYTITLE:Starting Manual Continuity Check}}

← Older revision		Revision as of 19:43, 9 July 2013
Line 1:		Line 1:
−	=== '''''Applies to version(s): ~~v2.6,~~ v2.7.''''' ===	+	=== '''''Applies to version(s): v2.7.''''' ===
	{{DISPLAYTITLE:Starting Manual Continuity Check}}		{{DISPLAYTITLE:Starting Manual Continuity Check}}

@@ Line 7: / Line 7: @@
 - Select '''SS7->ISUP''' from the navigation panel
-- Click on the '''Status''' tab and click on the appropriate ISUP Stack
+- Click the '''Status''' tab and click on the appropriate ISUP Stack
-- Click on the '''Interfaces''' tab and select the appropriate ISUP Interface
+- Click the '''Interfaces''' tab and select the appropriate ISUP Interface
-- Click on the '''Circuit Groups''' tab and select the appropriate Circuit Group
+- Click the '''Circuit Groups''' tab and select the appropriate Circuit Group
 '''If you want to start a continuity check on all circuits of a circuit group:'''
 *Select '''Yes''' for'''Start continuity check''' and click on '''Apply states'''
-*Click on '''Now''' to refresh the status and see the result of the test. Some of the following stats should be modified:
+*Click '''Now''' to refresh the status and see the result of the test. Some of the following stats should be modified:
 **Total ccr success cnt
 **Total ccr fail cnt