Toolpack v2.3:Configuring a TMS Network System - Revision history

Luc Morissette: /* To configure a TMS Network */

2009-12-01T14:09:37Z

To configure a TMS Network

Ka-Lok Yeung: /* To configure a TMS Network */

2009-12-01T08:05:41Z

To configure a TMS Network

Allyntree: /* To configure a TMS Network */

2009-10-23T20:18:48Z

To configure a TMS Network

Allyntree: /* To configure a TMS Network */

2009-10-23T20:12:54Z

To configure a TMS Network

Allyntree: /* To configure a TMS Network */

2009-10-23T20:07:39Z

To configure a TMS Network

Allyntree: /* To configure a TMS Network */

2009-10-23T20:04:04Z

To configure a TMS Network

Allyntree: Created page with 'Two TMS1600 Switches can be configured to operate a TMS Network, thereby providing redundancy backup. One TMS1600 Switch is configured as the primary switch while the other is co…'

2009-10-23T20:00:29Z

Created page with 'Two TMS1600 Switches can be configured to operate a TMS Network, thereby providing redundancy backup. One TMS1600 Switch is configured as the primary switch while the other is co…'

New page

Two TMS1600 Switches can be configured to operate a TMS Network, thereby providing redundancy backup. One TMS1600 Switch is configured as the primary switch while the other is configured as the secondary or backup switch.

== To configure a TMS Network ==

'''1. Select 'TMS Network' from the navigation panel.'''

[[Image:Menu-tms-network.jpg|400px]]

The TMS network list is displayed.

'''2. Click Configure New TMS Network to access the TMS Network configuration window.'''

[[Image:Menu-configure-tms-network.jpg|600px]]

'''3. Select the name of the primary switch from the Primary Adapter field. This switch will operate as the active or main switch.'''
*Select the name of the secondary switch from the Secondary Adapter field. This switch will function as the backup switch.
*Click Create to save the configuration.

[[Image:Menu-create-TMS-configuration.jpg|600px]]

*The TMS Network was successfully created message is displayed.

[[Image:Menu-confirm-new-tms-configuration.jpg|600px]]

== Verifying Status ==
To verify the status of the TMS Network configuration, select Status from the Navigation panel.

@@ Line 18: / Line 18: @@
 *Select the name of the primary switch from the Primary Adapter field. This switch will operate as the active or main switch.'''
 *Select the name of the secondary switch from the Secondary Adapter field. This switch will function as the backup switch.
-*If you enable "Use Link Switch Over", switchover between TMS port A and B would be allowed. (This should be enabled if  dual TMS connection is available for redundancy.)
+*If you enable '''Use Link Switch Over''', switchover between TMS port A and B would be allowed. (This should be enabled if  dual TMS connection is available for redundancy.)
-*If you enable "Use Link Switch Over Recovery", TMS port A would become active again when available if switch to port B has occurred. Leaving this option off will cause less switchovers, and thus less clock glitches through the TMS system, but will make unpredictable which port is active at a given time.
+*If you enable '''Use Link Switch Over Recovery''', TMS port A would become active again when available if switch to port B has occurred. Leaving this option off will cause less switchovers, and thus less clock glitches through the TMS system, but will make unpredictable which port is active at a given time.
-*If you enable "Use Clock Ref. Recovery", the system will use the highest available external clock source of the TMS system (by highest I mean the first one in the list in the "Clocking" configuration of Toolpack). If this option is off, the system will remain on any secondary clock reference even after the primary is back. This also cause less clock switchovers, but make unpredictable which external clock source is used at a given time.
+*If you enable '''Use Clock Ref. Recovery''', the system will use the highest available external clock source of the TMS system (by highest I mean the first one in the list in the "Clocking" configuration of Toolpack). If this option is off, the system will remain on any secondary clock reference even after the primary is back. This also cause less clock switchovers, but make unpredictable which external clock source is used at a given time.
 *Click Save to save the configuration.

@@ Line 15: / Line 15: @@
-'''3. Select the name of the primary switch from the Primary Adapter field. This switch will operate as the active or main switch.'''
+'''3. Edit the parameters of the TMS Network
 *Select the name of the secondary switch from the Secondary Adapter field. This switch will function as the backup switch.
 *Click Save to save the configuration.

← Older revision		Revision as of 20:12, 23 October 2009
Line 12:		Line 12:
	'''2. Click Edit to access the TMS Network configuration window.'''		'''2. Click Edit to access the TMS Network configuration window.'''

−	[[Image:~~Menu-configure-tms-network~~.~~jpg~~\|~~600px~~]]	+	[[Image:Web_Portal_v2.3_TMS_Network_Edit.png\|700px]]

@@ Line 20: / Line 20: @@
-[[Image:Menu-create-TMS-configuration.jpg|600px]]
+[[Image:Web_Portal_v2.3_TMS_Network_Create.png|700px]]
 *The TMS Network was successfully created message is displayed.
-[[Image:Menu-confirm-new-tms-configuration.jpg|600px]]
+[[Image:Web_Portal_v2.3_TMS_Network_Successful.png|700px]]
 == Verifying Status ==
 To verify the status of the TMS Network configuration, select Status from the Navigation panel.

@@ Line 10: / Line 10: @@
-'''2. Click Configure New TMS Network to access the TMS Network configuration window.'''
+'''2. Click Edit to access the TMS Network configuration window.'''
 [[Image:Menu-configure-tms-network.jpg|600px]]
@@ Line 17: / Line 17: @@
 '''3. Select the name of the primary switch from the Primary Adapter field. This switch will operate as the active or main switch.'''
 *Select the name of the secondary switch from the Secondary Adapter field. This switch will function as the backup switch.
-*Click Create to save the configuration.
+*Click Save to save the configuration.

@@ Line 5: / Line 5: @@
 '''1. Select 'TMS Network' from the navigation panel.'''
-[[Image:Menu-tms-network.jpg|400px]]
+[[Image:Navigation_Panel_v2.3_TMS_Network.png]]
 The TMS network list is displayed.
@@ Line 26: / Line 26: @@
 [[Image:Menu-confirm-new-tms-configuration.jpg|600px]]
 == Verifying Status ==
 To verify the status of the TMS Network configuration, select Status from the Navigation panel.