Use Cases:TMG Performing M2UA Signaling Relay - Revision history

Luc Morissette at 16:13, 23 August 2019

2019-08-23T16:13:09Z

2017-09-21T18:06:28Z

LM Added Revise on Major (Link to configuration must adapt according to the version)

2016-09-30T18:28:42Z

2016-09-30T18:28:32Z

2016-09-30T18:26:17Z

Added link to Configuration page

2016-08-03T20:49:18Z

2016-08-03T20:48:34Z

2016-07-29T14:17:27Z

2016-07-29T14:16:59Z

2016-07-29T14:14:03Z

← Older revision		Revision as of 16:13, 23 August 2019
Line 1:		Line 1:
−	{{DISPLAYTITLE:TMG Performing ~~M2UA~~ Signaling Relay}}	+	{{DISPLAYTITLE:TMG Performing MTP2 Signaling Relay over M2UA}}
	=== '''''Applies to version(s): v2.9 and above''''' ===		=== '''''Applies to version(s): v2.9 and above''''' ===

← Older revision		Revision as of 18:06, 21 September 2017
Line 31:		Line 31:
	== References ==		== References ==
	*[[Toolpack:Protocol_Stack_Settings_B#M2UA.3C-.3EMTP2_Relay\|Configuring MTP2 to M2UA relay]]		*[[Toolpack:Protocol_Stack_Settings_B#M2UA.3C-.3EMTP2_Relay\|Configuring MTP2 to M2UA relay]]
		+	[[Category:Revise on Major]]

← Older revision		Revision as of 18:28, 30 September 2016
Line 1:		Line 1:
−	~~Editing Use Cases:TMG Performing M2UA Signaling Relay~~
−	~~WikitextPreviewChanges~~
−	~~BoldItalicEmbedded fileSignature and timestampLinkReferenceAdvancedSpecial charactersHelp~~
	{{DISPLAYTITLE:TMG Performing M2UA Signaling Relay}}		{{DISPLAYTITLE:TMG Performing M2UA Signaling Relay}}
	=== '''''Applies to version(s): v2.9 and above''''' ===		=== '''''Applies to version(s): v2.9 and above''''' ===

@@ Line 5: / Line 5: @@
 === '''''Applies to version(s): v2.9 and above''''' ===
-In this scenario, all messages from TDM network are relayed to the IP network via Sigtran: M2UA <br />
+In this scenario, all messages from TDM network are relayed to the IP network via Sigtran: M2UA. This can be used on a satellite link. <br />
 [[File:Diagram_M2UA_Replay_TBwiki.jpg|800px]]

← Older revision		Revision as of 18:26, 30 September 2016
Line 31:		Line 31:
	**No need to configure MTP3 part		**No need to configure MTP3 part
	\|}		\|}
		+
		+	== References ==
		+	*[[Toolpack:Protocol_Stack_Settings_B#M2UA.3C-.3EMTP2_Relay\|Configuring MTP2 to M2UA relay]]

@@ Line 7: / Line 7: @@
 In this scenario, all messages from TDM network are relayed to the IP network via Sigtran: M2UA <br />
-[[File:Diagram_M2UA_Replay.jpg|800px]]
+[[File:Diagram_M2UA_Replay_TBwiki.jpg|800px]]
 <br /><br />
 <br />

@@ Line 2: / Line 2: @@
 WikitextPreviewChanges
 BoldItalicEmbedded fileSignature and timestampLinkReferenceAdvancedSpecial charactersHelp
 {{DISPLAYTITLE:TMG Performing M2UA Signaling Relay}}
 === '''''Applies to version(s): v2.9 and above''''' ===

@@ Line 18: / Line 18: @@
 {| colspan="4" border="1" class="wikitable"
-! width="400" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Configure TMG: M2UA Replay
+! width="400" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Configure TMG: M2UA Relay
 ! width="400" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Configure TMG: M2UA SG
 |-

@@ Line 12: / Line 12: @@
 <br />
 Note: This implementation, although based on standards, is proprietary.
-Normally, one end is the SG and the other is the MGC. So in this use case, one of the TMGs simulates the MGC. All of this is transparent to the TDM devices interconnected over IP.<br />
+Normally, one end is the SG and the other is the MGC.