Toolpack v2.5:Configuring IP Interfaces
From TBwiki
(Difference between revisions)
(moved Toolpack v2.5:Configuring IP Interfaces to Configuring IP Interfaces: New naming convention) |
(return page content to redirect page) |
||
| Line 1: | Line 1: | ||
| − | + | The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following: | |
| + | |||
| + | *IP Address | ||
| + | *Netmask | ||
| + | *Gateway | ||
| + | |||
| + | <br> | ||
| + | |||
| + | == To configure a VoIP0 or VoIP1 port == | ||
| + | |||
| + | 1. Select '''IP Interfaces''' from the navigation panel: | ||
| + | |||
| + | [[Image:Toolpack v2.5 Navigation Panel IP Interfaces.png]] | ||
| + | |||
| + | <br> 2. Click '''Edit''' from the IP Interfaces Information panel: | ||
| + | |||
| + | [[Image:Toolpack v2.5 Edit IP Interface.png]] | ||
| + | |||
| + | <br> 3. Configure the IP port: | ||
| + | |||
| + | *Indicate whether or not to use '''DHCP''' on this port | ||
| + | *Enter an '''IP address''' | ||
| + | *Enter a '''Netmask''' | ||
| + | *Enter a '''gateway address''' | ||
| + | *Click '''Save''' | ||
| + | |||
| + | '''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. <br> | ||
| + | |||
| + | [[Image:Toolpack v2.5 Editing IP Interface.png]] | ||
| + | |||
| + | <br> | ||
| + | |||
| + | 4. The changes are displayed in the IP interfaces information panel: | ||
| + | |||
| + | [[Image:Toolpack v2.5 IP Interface Edited.png]] | ||
| + | |||
| + | <br> '''IMPORTANT!''' The system will display the following notice, describing steps to apply your new configuration: | ||
| + | |||
| + | [[Image:Toolpack v2.5 IP Interface Alert.png]] | ||
| + | |||
| + | <br> | ||
| + | |||
| + | 5. Activate the configuration | ||
| + | |||
| + | Systems -> Edit -> Activate | ||
| + | |||
| + | |||
| + | |||
| + | 6. Reboot the adapter (will drop active calls) | ||
| + | |||
| + | Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter | ||
| + | |||
| + | It will take about 1.5 minutes to restart the unit. | ||
| + | |||
| + | == List of Parameters == | ||
| + | |||
| + | *[[Parameter: Use DHCP|Use DHCP]] | ||
| + | *[[Parameter: IP Address|IP Address]] | ||
| + | *[[Parameter: Netmask|Netmask]] | ||
| + | *[[Parameter: Gateway|Gateway]] | ||
Latest revision as of 09:08, 26 February 2013
The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:
- IP Address
- Netmask
- Gateway
To configure a VoIP0 or VoIP1 port
1. Select IP Interfaces from the navigation panel:
2. Click Edit from the IP Interfaces Information panel:
3. Configure the IP port:
- Indicate whether or not to use DHCP on this port
- Enter an IP address
- Enter a Netmask
- Enter a gateway address
- Click Save
Note: The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets.
4. The changes are displayed in the IP interfaces information panel:
IMPORTANT! The system will display the following notice, describing steps to apply your new configuration:
5. Activate the configuration
Systems -> Edit -> Activate
6. Reboot the adapter (will drop active calls)
Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter
It will take about 1.5 minutes to restart the unit.
