Toolpack:Creating an SCCP Route A
From TBwiki
(Difference between revisions)
(→List of Parameters) |
m (typo) |
||
| (11 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | Now that you have created an [[SCCP]] LSAP, you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system. | + | === '''''Applies to version(s): v2.5, v2.6, v2.7''''' === |
| + | {{DISPLAYTITLE:Creating an SCCP Route}} | ||
| + | Now that you have created an [[SCCP]] [[LSAP]], you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system. | ||
This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC). | This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC). | ||
| Line 11: | Line 13: | ||
2- Configure the new SCCP Route: | 2- Configure the new SCCP Route: | ||
| − | * Choose a | + | * Choose a [[Parameter: Name|Name]] for the new route |
| − | * Select a | + | * Select a [[Parameter: Protocol Type|Protocol Variant]] |
| − | * Select a | + | * Select a [[Parameter: Replication Mode|Replication Mode]] (ANSI96 and TELCORDIA variants) |
| − | * Select an | + | * Select an [[Parameter: SLS Mask|SLS Mask]] (ANSI and TELCORDIA protocol variants) |
| − | * Select a | + | * Select a [[Parameter: Destination Point Code|Destination Point Code]] for this route |
* Click '''Create''' | * Click '''Create''' | ||
| Line 24: | Line 26: | ||
[[Image:Toolpack_v2.5_SCCP_Route_Created.png]] | [[Image:Toolpack_v2.5_SCCP_Route_Created.png]] | ||
| + | 4- Configure [[SCCP Route Backup Point Code]] | ||
| + | |||
| + | * Assign [[Parameter: SCCP Backup Point Code| Backup Point Codes]] to use in case this route's [[DPC]] is not available. | ||
| + | [[Image:SCCP_Route_Backup_PC.png]] | ||
| + | |||
| + | * '''Note: For each selected point codes, a valid SCCP route must exist'''. | ||
| + | |||
| + | |||
| + | 5- '''Next Step:''' [[Toolpack_v2.5:Creating_an_SCCP_SSN|Create an SCCP SSN]] | ||
==List of Parameters== | ==List of Parameters== | ||
| Line 32: | Line 43: | ||
* [[Parameter: SLS Mask|SLS Mask]] (For ANSI and TELCORDIA variants only) | * [[Parameter: SLS Mask|SLS Mask]] (For ANSI and TELCORDIA variants only) | ||
* [[Parameter: Destination Point Code|Destination Point Code]] | * [[Parameter: Destination Point Code|Destination Point Code]] | ||
| + | |||
| + | ==Navigation== | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | ! Previous !! Next | ||
| + | |- | ||
| + | | [[Toolpack_v2.5:Creating_an_SCCP_LSAP|Create an SCCP LSAP]] || [[Toolpack_v2.5:Creating_an_SCCP_SSN|Create an SCCP SSN]] | ||
| + | |} | ||
Latest revision as of 12:37, 26 September 2014
Applies to version(s): v2.5, v2.6, v2.7
Now that you have created an SCCP LSAP, you must create a new SCCP route for your system. This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).
To Create an SCCP Route:
1- Click Create new Sccp Route in the SCCP LSAP configuration window
2- Configure the new SCCP Route:
- Choose a Name for the new route
- Select a Protocol Variant
- Select a Replication Mode (ANSI96 and TELCORDIA variants)
- Select an SLS Mask (ANSI and TELCORDIA protocol variants)
- Select a Destination Point Code for this route
- Click Create
3- Verify that the "SccpRoute was successfully created" message appears
4- Configure SCCP Route Backup Point Code
- Assign Backup Point Codes to use in case this route's DPC is not available.
- Note: For each selected point codes, a valid SCCP route must exist.
5- Next Step: Create an SCCP SSN
List of Parameters
- Name
- Protocol Variant
- Replication Mode
- SLS Mask (For ANSI and TELCORDIA variants only)
- Destination Point Code
| Previous | Next |
|---|---|
| Create an SCCP LSAP | Create an SCCP SSN |
