TMG:Change Internal Subnets Procedure

From TBwiki
(Difference between revisions)
Jump to: navigation, search
(change link name)
 
(37 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
This article explains how to modify the internal subnets of a TMG800 Unit.
+
__NoToc__
 +
=== '''''Applies to version v2.8 and above''''' ===
 +
{{DISPLAYTITLE:Changing the Internal Subnets}}
  
−
The TMG800 unit '''need to use private internal subnets''' for communication between internal modules, and between the two units of a TMG800 1+1 system.
+
This procedure describes how to change the internal subnets (IP addresses) of a TMG800, TMG3200 or TMG7800 Unit.
  
−
== 1. Resetting the Unit role ==
+
[[TMG:Change Internal Subnets|Click here for more information on internal subnets of TMG Units]]
−
'''Note''': If your Unit was just shipped, it does not yet has it's "role" configured, and you can skip to step 2 below.
+
  
−
To change the internal IP addresses of a TMG800 Unit, it's required to reset the Unit's role (Standlone/Primary/Secondary). Once the role is reset, the Web Portal will show steps to re-configure the Unit's Role, and at the same time select the internal Subnets to use.
 
  
−
To reset the Unit's role:
+
== Change the IP Addresses of the TMG7800 Telecom Units ==
−
=== Log into the Unit's Web Portal ===
+
  
−
=== Go to "Hosts" (on the left menu) ===
 
−
[[Image:Toolpack_Navigation_Change_Subnets_1_A.png]]
 
−
<br/><br/>
 
  
−
=== Click the "Status" tab ===
+
'''Note: For the TMG800 and TMG3200, skip this step.'''
−
[[Image:Toolpack_Navigation_Change_Subnets_2_A.png]]
+
−
<br/><br/>
+
  
−
=== Click on the serial number of the Unit ===
 
−
[[Image:Toolpack_Navigation_Change_Subnets_3_A.png]]
 
−
<br/><br/>
 
  
−
=== Select Action "Reset Host Role" ===
+
Before you change the host's subnets, make sure that all of the Telecom Units of your TMG7800 system have had their IP addresses changed to the new subnet. For each  Telecom unit of the TMG7800 system, do the following:
−
[[Image:Toolpack_Navigation_Change_Subnets_4_A.png]]
+
−
<br/><br/>
+
  
−
=== Click "Apply Action" ===
+
* Connect to Telecom Unit's shell (using Telnet, or serial port)
−
[[Image:Toolpack_Navigation_Change_Subnets_5_A.png]]
+
* Use "set_net" command
−
<br/><br/>
+
* Follow the instructions
 +
* Reboot the unit
  
−
=== Refresh the web page until role selection appears ===
+
== Resetting the Host Role of the Unit ==
−
[[Image:Toolpack_Navigation_Change_Subnets_6_A.png]]
+
'''Note: If your Unit was just shipped, it does not yet has it's "role" configured, and you can skip this step.'''
−
<br/>(this can take a minute...)
+
−
<br/><br/>
+
  
−
=== Click "Continue", answer the questions ===
 
−
[[Image:Toolpack_Navigation_Change_Subnets_7_A.png]]
 
−
<br/><br/>
 
  
−
=== Click on "change internal subnets" ===
+
Changing the internal IP addresses of a TMG requires that the Unit's role (Standlone/Primary/Secondary) is reset. Once the role is reset, the Web Portal displays the  steps to reconfigure the Unit's Role, and configure the internal Subnets.
−
[[Image:Toolpack_Navigation_Change_Subnets_8_A.png]]
+
−
<br/><br/>
+
  
−
=== Change subnets as required, click "continue" ===
+
[[Toolpack:Reset_HostRole_A|Reset the Host Role for v2.8]]
−
[[Image:Toolpack_Navigation_Change_Subnets_9_A.png]]
+
−
<br/>'''Note:''' You may not see some of the options in the above screenshot. Only options available for current product are shown on this page.
+
−
<br/><br/>
+
  
−
=== Click "continue" and "confirm" ===
+
== Configure the Unit's Role ==
−
Confirmation pages will appear, continue or confirm if you're satisfied with your choices.
+
You can configure the host role of your unit, to the following choices:
−
<br/><br/>
+
* [[Toolpack:Host_Standalone_A|Standalone for v2.8]]
 +
* [[Toolpack:Host_1Plus1_Primary_A|1+1 Primary for v2.8]]
 +
* [[Toolpack:Host_1Plus1_Secondary_A|1+1 Secondary for v2.8]]
  
−
=== Wait until configuration is completed ===
+
Make sure to repeat this operation for the two units of your 1+1 system, or the two hosts of your TMG7800 system. In addition, make sure to start with the primary.
−
[[Image:Toolpack_Navigation_Change_Subnets_10_A.png]]
+
−
<br/>(This can take a few minutes...)
+
−
<br/><br/>
+
  
−
=== Login page will be back ===
+
 
−
[[Image:Toolpack_Navigation_Change_Subnets_11_A.png]]
+
[[Category:Gateway_OAM&P|Management]]
−
<br/><br/>
+
[[Category:Revise on Major]]

Latest revision as of 13:51, 2 April 2015

Applies to version v2.8 and above

This procedure describes how to change the internal subnets (IP addresses) of a TMG800, TMG3200 or TMG7800 Unit.

Click here for more information on internal subnets of TMG Units


Change the IP Addresses of the TMG7800 Telecom Units

Note: For the TMG800 and TMG3200, skip this step.


Before you change the host's subnets, make sure that all of the Telecom Units of your TMG7800 system have had their IP addresses changed to the new subnet. For each Telecom unit of the TMG7800 system, do the following:

  • Connect to Telecom Unit's shell (using Telnet, or serial port)
  • Use "set_net" command
  • Follow the instructions
  • Reboot the unit

Resetting the Host Role of the Unit

Note: If your Unit was just shipped, it does not yet has it's "role" configured, and you can skip this step.


Changing the internal IP addresses of a TMG requires that the Unit's role (Standlone/Primary/Secondary) is reset. Once the role is reset, the Web Portal displays the steps to reconfigure the Unit's Role, and configure the internal Subnets.

Reset the Host Role for v2.8

Configure the Unit's Role

You can configure the host role of your unit, to the following choices:

Make sure to repeat this operation for the two units of your 1+1 system, or the two hosts of your TMG7800 system. In addition, make sure to start with the primary.

Retrieved from "https://docs.telcobridges.com/mediawiki/index.php?title=TMG:Change_Internal_Subnets_Procedure&oldid=18115"
Personal tools