TMG:Change Internal Subnets Procedure
From TBwiki
(Difference between revisions)
(→Configure the Unit's Role: removed content and referred to Host role selection choices in the Web Portal 2.8 Host Role Configuration section.) |
(change link name) |
||
| (20 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | + | __NoToc__ | |
| + | === '''''Applies to version v2.8 and above''''' === | ||
| + | {{DISPLAYTITLE:Changing the Internal Subnets}} | ||
| − | + | This procedure describes how to change the internal subnets (IP addresses) of a TMG800, TMG3200 or TMG7800 Unit. | |
[[TMG:Change Internal Subnets|Click here for more information on internal subnets of TMG Units]] | [[TMG:Change Internal Subnets|Click here for more information on internal subnets of TMG Units]] | ||
| − | |||
| − | |||
| − | Before | + | == Change the IP Addresses of the TMG7800 Telecom Units == |
| + | |||
| + | |||
| + | '''Note: For the TMG800 and TMG3200, skip this step.''' | ||
| + | |||
| + | |||
| + | Before you change the host's subnets, make sure that all of the Telecom Units of your TMG7800 system have had their IP addresses changed to the new subnet. For each Telecom unit of the TMG7800 system, do the following: | ||
| − | |||
* Connect to Telecom Unit's shell (using Telnet, or serial port) | * Connect to Telecom Unit's shell (using Telnet, or serial port) | ||
* Use "set_net" command | * Use "set_net" command | ||
| − | * Follow instructions | + | * Follow the instructions |
* Reboot the unit | * Reboot the unit | ||
| + | == Resetting the Host Role of the Unit == | ||
| + | '''Note: If your Unit was just shipped, it does not yet has it's "role" configured, and you can skip this step.''' | ||
| − | |||
| − | |||
| − | Changing the internal IP addresses of a TMG requires | + | Changing the internal IP addresses of a TMG requires that the Unit's role (Standlone/Primary/Secondary) is reset. Once the role is reset, the Web Portal displays the steps to reconfigure the Unit's Role, and configure the internal Subnets. |
| − | [[Toolpack:Reset_HostRole_A| | + | [[Toolpack:Reset_HostRole_A|Reset the Host Role for v2.8]] |
== Configure the Unit's Role == | == Configure the Unit's Role == | ||
| − | You can configure the host role of your unit, to the following: | + | You can configure the host role of your unit, to the following choices: |
| − | * [[Toolpack:Host_Standalone_A|Standalone]] | + | * [[Toolpack:Host_Standalone_A|Standalone for v2.8]] |
| − | * [[Toolpack:Host_1Plus1_Primary_A|1+1 Primary]] | + | * [[Toolpack:Host_1Plus1_Primary_A|1+1 Primary for v2.8]] |
| − | * [[Toolpack:Host_1Plus1_Secondary_A|1+1 Secondary | + | * [[Toolpack:Host_1Plus1_Secondary_A|1+1 Secondary for v2.8]] |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | Make sure to start with the primary. | + | Make sure to repeat this operation for the two units of your 1+1 system, or the two hosts of your TMG7800 system. In addition, make sure to start with the primary. |
[[Category:Gateway_OAM&P|Management]] | [[Category:Gateway_OAM&P|Management]] | ||
| + | [[Category:Revise on Major]] | ||
Latest revision as of 13:51, 2 April 2015
Applies to version v2.8 and above
This procedure describes how to change the internal subnets (IP addresses) of a TMG800, TMG3200 or TMG7800 Unit.
Click here for more information on internal subnets of TMG Units
Change the IP Addresses of the TMG7800 Telecom Units
Note: For the TMG800 and TMG3200, skip this step.
Before you change the host's subnets, make sure that all of the Telecom Units of your TMG7800 system have had their IP addresses changed to the new subnet. For each Telecom unit of the TMG7800 system, do the following:
- Connect to Telecom Unit's shell (using Telnet, or serial port)
- Use "set_net" command
- Follow the instructions
- Reboot the unit
Resetting the Host Role of the Unit
Note: If your Unit was just shipped, it does not yet has it's "role" configured, and you can skip this step.
Changing the internal IP addresses of a TMG requires that the Unit's role (Standlone/Primary/Secondary) is reset. Once the role is reset, the Web Portal displays the steps to reconfigure the Unit's Role, and configure the internal Subnets.
Configure the Unit's Role
You can configure the host role of your unit, to the following choices:
Make sure to repeat this operation for the two units of your 1+1 system, or the two hosts of your TMG7800 system. In addition, make sure to start with the primary.
