Toolpack:Creating an M3UA Peer Server (SGP) B
From TBwiki
(Difference between revisions)
(New 2.8 article) |
(→List of Parameters) |
||
| (8 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
=== '''''Applies to version(s): v2.8''''' === | === '''''Applies to version(s): v2.8''''' === | ||
| − | {{DISPLAYTITLE:Creating an M3UA Peer | + | {{DISPLAYTITLE:Creating an M3UA Peer Server (SGP)}} |
| − | After you create an M3UA | + | After you create an M3UA peer signaling process, you must create a new M3UA peer server. A peer server is a logical entity on the IP network that is served by one or more PSPs. |
| − | To create an M3UA Peer | + | To create an M3UA Peer Server: |
| Line 13: | Line 13: | ||
2- Select an M3ua Network: | 2- Select an M3ua Network: | ||
| − | [[Image: | + | [[Image:SelectNetwork_SGP_0.png]] |
| − | 3- Click '''Create New M3ua Peer | + | 3- Click '''Create New M3ua Peer Server''' in the M3UA network configuration window: |
| − | [[Image: | + | [[Image:Create_M3UA_Peer_Server_SGP_0.png]] |
| − | 4- Configure the new M3UA | + | 4- Configure the new M3UA Server: |
* Enter a '''name''' for the peer server | * Enter a '''name''' for the peer server | ||
| Line 32: | Line 32: | ||
* Click '''Create''' | * Click '''Create''' | ||
| − | [[Image: | + | [[Image:Create_M3UA_Peer_Server_SGP_1.png]] |
| − | 5- Verify that the '''"M3ua | + | 5- Verify that the '''"M3ua Peer Server was successfully created"''' message appears |
| − | [[Image: | + | [[Image:Create_M3UA_Peer_Server_SGP_2.png]] |
| − | 6- Associate | + | 6- Associate the newly created peer server with a peer signaling process (PSP): |
| − | * Select a ''' | + | * Select a '''PSP''' from the list of available PSPs |
| − | * Click the '''"<<"''' button to associate | + | * Click the '''"<<"''' button to associate the PSP with the peer server |
| − | [[Image: | + | [[Image:Create_M3UA_Peer_Server_SGP_3.png]] |
| + | ==List of Parameters== | ||
| − | + | * [[Parameter: Name|Name]] | |
| + | * [[Parameter: Local|Local]] | ||
| + | * [[Parameter: Routing Context|Routing Context (RC)]] | ||
| + | * [[Parameter: Traffic Mode Type|Traffic Mode Type]] | ||
| − | |||
| − | |||
| − | + | '''Advanced Parameters''' | |
| − | + | * [[Parameter: Load Sharing Mode|Load Sharing Mode]] | |
| − | + | * [[Parameter: Required Available|Required Available]] | |
| − | + | * [[Parameter: Minimum Active Psps for load sharing|Minimum Active Psps for load sharing]] | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | * [[Parameter: | + | |
| − | * [[Parameter: | + | |
| − | * [[Parameter: | + | |
Latest revision as of 15:39, 26 June 2015
Applies to version(s): v2.8
After you create an M3UA peer signaling process, you must create a new M3UA peer server. A peer server is a logical entity on the IP network that is served by one or more PSPs.
To create an M3UA Peer Server:
1- Click M3UA in the navigation panel:
2- Select an M3ua Network:
3- Click Create New M3ua Peer Server in the M3UA network configuration window:
4- Configure the new M3UA Server:
- Enter a name for the peer server
- Create a remote Peer Server (PSRV) with a Routing Context (RC) value representing the remote side； Take the RC value from ASP configuration.
Note: 1) For SG/ASP this value is mandatory to be the same as the ASP local PSRV RC value 2) SG uses only remote peer servers, so local peer server (OPC) is NOT needed
- Select the Traffic Mode Type. For remote peer server, this field is used in ASPAC.
- Click Create
5- Verify that the "M3ua Peer Server was successfully created" message appears
6- Associate the newly created peer server with a peer signaling process (PSP):
- Select a PSP from the list of available PSPs
- Click the "<<" button to associate the PSP with the peer server
List of Parameters
Advanced Parameters
