Modify Fax Relay Profile F
From TBwiki
(Difference between revisions)
| (3 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
| − | |||
{{DISPLAYTITLE:Modifying FAX Relay Profile Settings}} | {{DISPLAYTITLE:Modifying FAX Relay Profile Settings}} | ||
<br> | <br> | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | |rowspan="3"|This article applies to: | ||
| + | |'''Product''' | ||
| + | |'''Version''' | ||
| + | |- | ||
| + | |Tmedia | ||
| + | |3.0, 3.2 | ||
| + | |- | ||
| + | |SBC | ||
| + | |3.0, 3.1 | ||
| + | |} | ||
'''To configure FAX Relay settings, do the following:''' | '''To configure FAX Relay settings, do the following:''' | ||
| Line 33: | Line 43: | ||
* [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration|Fax/Modem tones detection duration]] | * [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration|Fax/Modem tones detection duration]] | ||
* [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection|Enable early Fax/Modem tone detection]] | * [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection|Enable early Fax/Modem tone detection]] | ||
| − | * [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone| | + | * [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone|Switch to FAX relay upon CNG tone]] |
| + | * [[Parameter: Fax Modem Relay: Expected CNG tones|Expected CNG tones]] | ||
* [[Parameter: Fax Modem Relay: Switch to passthrough upon Bell ANS|Switch to passthrough upon Bell ANS]] | * [[Parameter: Fax Modem Relay: Switch to passthrough upon Bell ANS|Switch to passthrough upon Bell ANS]] | ||
<br> | <br> | ||
| Line 42: | Line 53: | ||
* [[Parameter: T.38 Parameters: Redundancy Count|Redundancy Count]] | * [[Parameter: T.38 Parameters: Redundancy Count|Redundancy Count]] | ||
* [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)|Transmission level (-1dBm unit)]] | * [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)|Transmission level (-1dBm unit)]] | ||
| + | * [[Parameter: T.38 Parameters: Prevent direct invite in T.38|Prevent direct invite in T.38]] | ||
<br> | <br> | ||
Fax/Modem Pass-through Parameters | Fax/Modem Pass-through Parameters | ||
Latest revision as of 13:15, 25 November 2020
| This article applies to: | Product | Version |
| Tmedia | 3.0, 3.2 | |
| SBC | 3.0, 3.1 |
To configure FAX Relay settings, do the following:
1- Click Fax Relay in the Editing Profile window, to display the customizable options.
2- Modify settings as required.
3- To configure NSE, check the Use NSE checkbox.
NOTE:
If NSE exchange is possible (negociated in the SDP), the switch to passthrough will happen in the RTP stream and no longer wiil occur with a SIP re-INVITE. This implementation of NSE currently only supports a switch to passthrough, which means that you can have NSE packets switching to T.38.
- Click Save
List of Parameters
Fax/Modem Relay
- Enable Fax/Modem Relay
- Detection Mode
- Relay Mode
- Modem vs. Fax distinction timeout
- Fax/Modem tones detection duration
- Enable early Fax/Modem tone detection
- Switch to FAX relay upon CNG tone
- Expected CNG tones
- Switch to passthrough upon Bell ANS
T.38 Parameters
- Use V.34
- Maximum Bit Rate
- Fill Bit Removal
- Redundancy Count
- Transmission level (-1dBm unit)
- Prevent direct invite in T.38
Fax/Modem Pass-through Parameters
