Toolpack:Adding an Adapter B
From TBwiki
(Difference between revisions)
(→Applies to version v2.6) |
(Fix typo: Is -> In) |
||
| (7 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
=== '''''Applies to version v2.6''''' === | === '''''Applies to version v2.6''''' === | ||
| − | {{DISPLAYTITLE:Adding | + | {{DISPLAYTITLE:Adding Telecom Hardware}} |
When you receive a new system, at least one hardware configuration will have been set in the [[Toolpack]] application server, by default. To add other hardware devices, you must use the Tmedia [[Web Portal]]. | When you receive a new system, at least one hardware configuration will have been set in the [[Toolpack]] application server, by default. To add other hardware devices, you must use the Tmedia [[Web Portal]]. | ||
| Line 14: | Line 14: | ||
| − | [[Image: | + | [[Image:CreateHardwareTmp_0_A.png]] |
| Line 20: | Line 20: | ||
| − | [[Image: | + | [[Image:CreateHardwareTmp_1_A.png]] |
| Line 26: | Line 26: | ||
* Enter the '''serial number''' of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur). | * Enter the '''serial number''' of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur). | ||
| − | * Select the appropriate '''hardware device''' from the | + | * Select the appropriate '''hardware device''' from the Type field. (In this case select TMP) |
| + | * Select the type of TDM lines that the hardware device will support. | ||
| + | * Indicate if the device will operate as a backup in a 1+1 configuration. If this is the first device being added, leave this field clear. | ||
| + | * Provide the amount of time in seconds, that the system will wait for calls to complete before shutting down for an upgrade. | ||
| + | * Enter the location in which the hardware device is installed. | ||
| + | * Enter a meaningful description as to the usage or purpose of the hardware device. | ||
* Select '''Enabled''' from the Target State field. | * Select '''Enabled''' from the Target State field. | ||
* Click '''Create''' | * Click '''Create''' | ||
| − | [[Image: | + | [[Image:CreateHardwareTmp_2_A.png]] |
| + | '''NOTE''' | ||
| + | The following image shows the 1+1 Backup field set. This is done for the addition a secondary TMP that will operate as the designated 1+1 backup in a 1+1 Group. | ||
| + | |||
| + | [[Image:CreateHardwareTmp_2_1_A.png]] | ||
4- Verify that the '''"Adapter was successfully created"''' message appears, and that the newly added hardware device appears in the '''Hardware List''' below | 4- Verify that the '''"Adapter was successfully created"''' message appears, and that the newly added hardware device appears in the '''Hardware List''' below | ||
| − | [[Image: | + | [[Image:CreateHardwareTmp_3_A.png]] |
==List of Parameters== | ==List of Parameters== | ||
Latest revision as of 10:12, 27 May 2015
Applies to version v2.6
When you receive a new system, at least one hardware configuration will have been set in the Toolpack application server, by default. To add other hardware devices, you must use the Tmedia Web Portal.
To add one or more additional hardware devices to the Toolpack system configuration, their serial numbers must be registered with the Toolpack application server.
To add a hardware device:
1- Click Hardware in the navigation panel
2- Click Create New Hardware, to add a new hardware device
3- Enter a name for the hardware device
- Enter the serial number of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).
- Select the appropriate hardware device from the Type field. (In this case select TMP)
- Select the type of TDM lines that the hardware device will support.
- Indicate if the device will operate as a backup in a 1+1 configuration. If this is the first device being added, leave this field clear.
- Provide the amount of time in seconds, that the system will wait for calls to complete before shutting down for an upgrade.
- Enter the location in which the hardware device is installed.
- Enter a meaningful description as to the usage or purpose of the hardware device.
- Select Enabled from the Target State field.
- Click Create
NOTE The following image shows the 1+1 Backup field set. This is done for the addition a secondary TMP that will operate as the designated 1+1 backup in a 1+1 Group.
4- Verify that the "Adapter was successfully created" message appears, and that the newly added hardware device appears in the Hardware List below
