Toolpack:Creating an SCCP SSN B
(Created page with "=== '''''Applies to version(s): v2.8''''' === {{DISPLAYTITLE:Creating an SCCP SSN}} After you have configured an SCCP Route, you can add SCCP Sub-System Number (SS...") |
|||
| (One intermediate revision by one user not shown) | |||
| Line 7: | Line 7: | ||
To Create an SCCP SSN: | To Create an SCCP SSN: | ||
| − | 1- | + | 1- Select '''SCCP''' from the navigation panel |
| − | |||
| − | 2- Configure the new SCCP SSN: | + | [[Image:Create_SCCP_Stack_0.png]] |
| + | |||
| + | |||
| + | 2- Select an SCCP Network | ||
| + | |||
| + | |||
| + | [[Image:Select_SCCP_Network_0.png]] | ||
| + | |||
| + | |||
| + | 3- Select an SCCP LSAP | ||
| + | |||
| + | |||
| + | [[Image:Select_SCCP_LSAP_0.png]] | ||
| + | |||
| + | |||
| + | 4- Select an SCCP Route | ||
| + | |||
| + | |||
| + | [[Image:Select_SCCP_Route_0.png]] | ||
| + | |||
| + | |||
| + | 5- Click '''Create New SSN''' from the SCCP route configuration window | ||
| + | |||
| + | [[Image:Create_SCCP_SSN_0.png]] | ||
| + | |||
| + | |||
| + | 6- Configure the new SCCP SSN: | ||
* Choose a [[Parameter: Sub-System Number|Sub-System Number]] for this route's DPC | * Choose a [[Parameter: Sub-System Number|Sub-System Number]] for this route's DPC | ||
| Line 19: | Line 44: | ||
* Click '''Create''' | * Click '''Create''' | ||
| − | [[Image: | + | [[Image:Create_SCCP_SSN_1.png]] |
| + | |||
| + | |||
| + | 7- Verify that the '''"SccpRtSsn was successfully created"''' message appears | ||
| − | + | [[Image:Create_SCCP_SSN_2.png]] | |
| − | |||
| − | + | 8- Configure [[SCCP Route SSN Backup Point Code]] | |
* Assign [[Parameter: SCCP Backup Point Code| Backup Point Codes]] to use in case this peer [[SSN]] is not available. | * Assign [[Parameter: SCCP Backup Point Code| Backup Point Codes]] to use in case this peer [[SSN]] is not available. | ||
| − | [[Image: | + | [[Image:Create_SCCP_SSN_3.png]] |
* '''Note: For each selected point codes, a valid SCCP route must exist'''. | * '''Note: For each selected point codes, a valid SCCP route must exist'''. | ||
Latest revision as of 12:58, 26 September 2014
Applies to version(s): v2.8
After you have configured an SCCP Route, you can add SCCP Sub-System Number (SSN) on the route.
SCCP Sub-System Number are used to identify applications of this route's DPC. SCCP managament will maintain the availability state for each SSN associated to this route's DPC. The SSN management status affects the routing decision. If a peer SSN is unavailable, the SCCP stack will try an alternate DPC/route.
To Create an SCCP SSN:
1- Select SCCP from the navigation panel
2- Select an SCCP Network
3- Select an SCCP LSAP
4- Select an SCCP Route
5- Click Create New SSN from the SCCP route configuration window
6- Configure the new SCCP SSN:
- Choose a Sub-System Number for this route's DPC
- Select a Replication Mode (ANSI and Telcordia only)
- Select the First Concerned Point Code that requires immediate notification upon state change of this peer SSN
- Select the Second Concerned Point Code that requires immediate notification upon state change of this peer SSN
- Click Create
7- Verify that the "SccpRtSsn was successfully created" message appears
8- Configure SCCP Route SSN Backup Point Code
- Assign Backup Point Codes to use in case this peer SSN is not available.
- Note: For each selected point codes, a valid SCCP route must exist.
