Toolpack:Configuring VoIP Interfaces C
From TBwiki
(Difference between revisions)
(→To configure a VoIP0 or VoIP1 port: , revised step 6) |
|||
| (6 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
{{DISPLAYTITLE:Configuring VoIP Interfaces}} | {{DISPLAYTITLE:Configuring VoIP Interfaces}} | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | |rowspan="3"|This article applies to: | ||
| + | |'''Product''' | ||
| + | |'''Version''' | ||
| + | |- | ||
| + | |Tmedia | ||
| + | |2.8, 2.9, 2.10, 3.0, 3.2 | ||
| + | |} | ||
The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following: | The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following: | ||
| Line 16: | Line 24: | ||
[[Image:Create Voip Interface_0.png]] | [[Image:Create Voip Interface_0.png]] | ||
| − | <br> 2. | + | <br> 2. Click '''Create New IP Interface''' from the IP Interfaces Information panel: |
| − | [[Image:Create | + | [[Image:Create Voip_Interface_1a.png]] |
<br> 3. Configure the IP port: | <br> 3. Configure the IP port: | ||
| Line 60: | Line 68: | ||
== List of Parameters == | == List of Parameters == | ||
| − | *[[Parameter: Use DHCP|Use | + | *[[Parameter: Interface name|Interface name]] |
| + | *[[Parameter: Services to use|Services to use]] | ||
| + | *[[Parameter: Virtual port|Virtual port]] | ||
| + | *[[Parameter: Use DHCP|Use dynamic IP]] | ||
*[[Parameter: IP Address|IP Address]] | *[[Parameter: IP Address|IP Address]] | ||
*[[Parameter: Netmask|Netmask]] | *[[Parameter: Netmask|Netmask]] | ||
*[[Parameter: Gateway|Gateway]] | *[[Parameter: Gateway|Gateway]] | ||
Latest revision as of 14:34, 10 December 2020
| This article applies to: | Product | Version |
| Tmedia | 2.8, 2.9, 2.10, 3.0, 3.2 |
The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:
- IP Address
- Netmask
- Gateway
To configure a VoIP0 or VoIP1 port
1. Select IP Interfaces from the navigation panel:
2. Click Create New IP Interface from the IP Interfaces Information panel:
3. Configure the IP port:
- Enter a name for the interface
- Select a service to use for the IP inteface
- Select a Virtual port from which IP packets will exit.
- Indicate whether or not to use dynamic IP will be used on this inteface. For example DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
- Enter an IP address
- Enter a Netmask
- Enter a gateway address
- Click Save
Note: The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets.
4. The changes are displayed in the IP interfaces information panel:
5. Activate the configuration
Systems -> Edit -> Activate
6. It is necessary to reboot the adapters if you are using the vlan from 3441 to 3450 only.
Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter
It will take about 1.5 minutes to restart the unit.
Note: in a 1+1 system, both units must be restarted.
