Toolpack:Creating an M3UA SAP (IPSP) B
From TBwiki
(Difference between revisions)
m (moved Toolpack:Creating an M3UA SAP B to Toolpack:Creating an M3UA SAP (IPSP) B: Consistency) |
(→List of Parameters) |
||
| (3 intermediate revisions by one user not shown) | |||
| Line 42: | Line 42: | ||
* [[Parameter: SCTP Adapter|SCTP Adapter]] | * [[Parameter: SCTP Adapter|SCTP Adapter]] | ||
* [[Parameter: SCTP Source Port|SCTP Source Port]] | * [[Parameter: SCTP Source Port|SCTP Source Port]] | ||
| + | |||
| + | '''M3UA SAP Timers''' | ||
| + | * [[Parameter: SCTP Primitive Timer|SCTP Primitive Timer]] | ||
| + | * [[Parameter: SCTP Association Timer|SCTP Association Timer]] | ||
| + | |||
| + | |||
| + | <div class="mw-collapsible mw-collapsed" data-collapsetext="SCTP SAP Advanced Parameters" data-expandtext="SCTP SAP Advanced Parameters" style="width: 400px;"> | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | |||
| + | * [[Parameter: Maximum data size|Maximum data size]] | ||
| + | * [[Parameter: Maximum ACK delay|Maximum ACK delay]] | ||
| + | * [[Parameter: Maximum datagram before ACK|Maximum datagram before ACK]] | ||
| + | * [[Parameter: Initial Retransmission Timeout (RTO)|Initial Retransmission Timeout (RTO)]] | ||
| + | * [[Parameter: Minimum Retransmission Timeout (RTO)|Minimum Retransmission Timeout (RTO)]] | ||
| + | * [[Parameter: Maximum Retransmission Timeout (RTO)|Maximum Retransmission Timeout (RTO)]] | ||
| + | * [[Parameter: Freeze timer|Freeze timer]] | ||
| + | * [[Parameter: Bundle timer|Bundle timer]] | ||
| + | * [[Parameter: Cookie life time|Cookie life time]] | ||
| + | * [[Parameter: Delay between heartbeat|Delay between heartbeat]] | ||
| + | * [[Parameter: Maximum datagram burst|Maximum datagram burst]] | ||
| + | * [[Parameter: Maximum heartbeat at each RTO|Maximum heartbeat at each RTO]] | ||
| + | * [[Parameter: Shutdown Guard Timer|Shutdown Guard Timer]] | ||
| + | * [[Parameter: Handle INIT datagram|Handle INIT datagram]] | ||
| + | * [[Parameter: Abort negociation if nb. streams mismatch|Abort negociation if nb. streams mismatch]] | ||
| + | * [[Parameter: Flow-control up threshold|Flow-control up threshold]] | ||
| + | * [[Parameter: Flow-control down threshold|Flow-control down threshold]] | ||
| + | |||
| + | |} | ||
| + | </div> | ||
Latest revision as of 12:30, 28 September 2015
Applies to version(s): v2.8
Once an M3UA configuration is created, you must then create a new M3UA service access point (SAP) for your system. The SAP is an identifying label for endpoints in your network.
To create an M3UA SAP:
1- Click M3UA in the navigation panel:
2- Click Create New M3ua Sap in the M3UA configuration panel
3- Configure the new SAP:
- Enter a name for the SAP
- Select an Unit to use
- Select an SCTP source port
- Click Create
4- Verify that the "M3ua Sap was successfully created" message appears
5- Associate an IP interface with the new SAP:
- Select an available IP interface
- Click the"<<" button to associate the interface with the SAP
List of Parameters
M3UA SAP Timers
